Need Replacement Mounting Hardware for the Tow-Rax Removable Wheel Chock w/ Wood Screws TWSPWC

Question

Question:

Can I order the Mounting hardware separate? TWSPWC

asked by: Hein

0

Expert Reply:

The replacement hardware screws that come with the Tow-Rax Removable Wheel Chock w/ Wood Screws, part # TWSPWC, are listed as part # TWSPWFKW.

If you need to mount the Tow-Rax Removable Wheel Chock to a metal floor then you will want part # TWPH2770, which includes mounting hardware for both wood and metal flooring.

expert reply by: Jon G

0

Answer 1

The Tow-Rax Removable Wheel Chock #TWSPWC3BT can be installed on either wood or metal surfaces using the hardware kit part #TWPH2770. You will need a drill with 7/16-inch bit for wood floors or a 9/16-inch bit for metal floors as well as a 3/16-inch…

view full answer...

Answer 2

For additional mounting hardware for the Tow-Rax Chock part #TWSPWM you would want the part #TWPH2770. This comes with hardware for both wood and metal surfaces.

view full answer...

Answer 3

I do not have any information on the Condor Chocks. I have not had any interaction with their product lines. I would follow their recommendations for installation. With heavier bikes like that I would imagine that the use of large washers or backing…

view full answer...

Answer 4

Probably the best option we can offer is an idea my Dad used in his enclosed motorcycle trailer. He mounted wheel chocks to a piece of plywood like the part #TWSPWM so that he could easily remove the chocks whenever he wanted the floor clearance.…

view full answer...

Answer 5

You are going to have to install wheel chocks more to the center of your trailer so that the handlebars of your dirt bikes would not interfere with the trailer walls. For that the Tow Rax part #TWSPWM would be a great option. Check out the install…

view full answer...

Answer 6

For an wheel chock that is easily removable, I recommend the Rackem chock, #RA-17. This chock has a base that mounts to the trailer floor and the chock part can easily be removed by loosening the wing nuts at the front. This chock accepts wheels up…

view full answer...

Answer 7

When installing the Tow-Rax Removable Wheel Chock w/ Wood Screws part #TWSPWM there really isn't a set material thickness it needs to be in. It does not carry any type of weight rating. It is meant to act as a stop for your wheel and to keep it…

view full answer...

Answer 8

I spoke to my contact at Tow Rax and she told me that to install the Mounting Hardware #TWSPWFKW you will have to use a 3/8 inch drill bit and they are the screws and anchors are 1 inch long. There is no wood that comes with this hardware kit.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...