Can HtdraStar EOH Adapter Be Attached To Wiring On Actuator Using Quick Splice Connectors

Question

Question:

Hi First love eTrailer. Question regarding HBA CAM If I get a HBA cam for my Hydra star Fifth wheel trailer that is already installed in the heated cargo bay CAN i use a wiring tap connector to tap into the actuator for the blue and white wire. 18-24 gauge blue tap connector It would be very easy as the actuator is in a difficult place versus cutting wire wires and crimping. Since covered and warm no worry for the connections if outside of course would shrink wrap Thanks again for the good service and expert opinions and answers I cannot paste photo of the connector, to this message. But common for auto wiring lay solid wire in open and push in end of the other wire and close clam sheel and click shut. Hope explained correctly

asked by: Brian

1

Helpful Expert Reply:

I attached a link to an installation video for the # HBA-CAM you can check out.

At About the 6:25 mark on the video, the electrical connection is shown. As long as you have a solid connection between the Actuator and the # HBA-CAM, it would work.

expert reply by: Jeffrey L

1

Answer 1

The Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes #HS481-8067 is designed to be completely plug-and-play so the female end of the 7-way would need to connect to the 7-way cable that's already installed on the…

view full answer...

Answer 2

As you can see on the attached photo, the wiring diagram for HydraStar Adapter #HBA-CAM shows there can be a 25-40 amp circuit breaker in-line with the black wiring which goes from the battery's positive terminal to the adapter. I would…

view full answer...

Answer 3

First, check to see if the factory brake controller on your 2015 GMC Sierra 2500 has an electric over hydraulic mode. I know that the new Ram's have that mode and if your Chevy also does then you would not need any sort of adapter. The…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...