Self Tapping Screw for Sway Control Ball Plate # RP58062 Recommendation

Question

Question:

I just purchased a replacement anti-sway ball plate because I sold my old trailer and forgot to get the old one off. The new one didnt come with screws. Can you recommend type and size of screws to purchase locally or can bolts with lock washers and nuts be used? If so, what size bolts do you recommend?

asked by: Eric

0

Expert Reply:

The bolts that come with this kit are # 24-9x1 inch self tapping screws. We sell them individually, they are Self Tapping Screw for Sway Control Ball Plate Assembly, part # 3403.

expert reply by: Jameson C

0

Answer 1

The Kodiak Hydraulic Brake Line Kit part #18SI-BLKIT doesn't come with hardware for the liner holders. The reason for this is that the exact hardware you need will vary by application and preference. In most cases, self-tapping screws will…

view full answer...

Answer 2

You will likely need some self-tapping screws. They are available in a set of 4, #CR80430. These are stainless steel screws so they won't corrode.

view full answer...

Answer 3

The Bright Way Trailer Breakaway Kit with Switch, 12V, 5-Amp-Hour Battery, and Charger #3802339 does not come with mounting hardware; you would need to supply your own self-tapping screws from a local hardware store. If you were looking for a…

view full answer...

Answer 4

If you are concerned with how to mount the Kodiak Tee Fitting part #BH-T-3FIF then I recommend using the Titan Tee Fitting part #T0778500. This fitting comes with a mounting bracket so you do not have to worry about the tee bouncing around. They…

view full answer...

Answer 5

If your current bolts are 5/16 inch, then the Self-Drilling Screw Hardware for Snap-Loc E-Track Tie-Down Anchors - Qty 4 #SLHSDDS-P should work just fine as long as the extra 1/2 inch in length isn't an issue. The self-tapping portion…

view full answer...

Answer 6

The wheel cylinder on the Hydraulic Trailer Brake Kit #AKUBRK-35 you were looking at uses the standard 3/8" x 24 Threads Per Inch brake line fittings. I included a video of the Kit #AKUBRK-35 for you to take a look at.

view full answer...

Answer 7

To install ball plate #RP58062 you will need to drill 4 holes using an 11/32 (.343) drill bit for 1/8" (.125) or thicker trailer tongue material, or a 9/32" (.281) drill bit for thinner material. Then you will line up the plate with the 4…

view full answer...

Answer 8

The Reese Friction Sway Control Kit part #83660 uses an 11/32" drill bit for material 1/8" and over and a 9/32" drill bit for material thinner than that. This kit uses the same Self Tapping Screw for Sway Control Ball Plate part #3403…

view full answer...

Answer 9

The Demco Hydraulic Brake Actuator part #DM72VR is a great option to replace an Atwood 82543. That said, it does not come with any sort of reverse lockout feature therefore in order to reverse without the brakes locking up you will either need to add…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Self Tapping Screw for Sway Control Ball Plate # RP58062 Recommendation

Product Page this Question was Asked From

Continue Researching