Self-Tapping Screws to Install Cruiser Accessories License Plate Mounting Plate

Question

Question:

what screws do I need to install this to my bumper, the only reviewer that you have posted says this does not have screws to install to bumper, so what ones do I need and do you sell them?

asked by: C D

0

Expert Reply:

You will likely need some self-tapping screws. They are available in a set of 4, # CR80430. These are stainless steel screws so they won't corrode.

expert reply by: Michael H

0

Answer 1

If you are concerned with how to mount the Kodiak Tee Fitting part #BH-T-3FIF then I recommend using the Titan Tee Fitting part #T0778500. This fitting comes with a mounting bracket so you do not have to worry about the tee bouncing around. They…

view full answer...

Answer 2

If your current bolts are 5/16 inch, then the Self-Drilling Screw Hardware for Snap-Loc E-Track Tie-Down Anchors - Qty 4 #SLHSDDS-P should work just fine as long as the extra 1/2 inch in length isn't an issue. The self-tapping portion…

view full answer...

Answer 3

The Bright Way Trailer Breakaway Kit with Switch, 12V, 5-Amp-Hour Battery, and Charger #3802339 does not come with mounting hardware; you would need to supply your own self-tapping screws from a local hardware store. If you were looking for a…

view full answer...

Answer 4

The Kodiak Hydraulic Brake Line Kit part #18SI-BLKIT doesn't come with hardware for the liner holders. The reason for this is that the exact hardware you need will vary by application and preference. In most cases, self-tapping screws will…

view full answer...

Answer 5

The wheel cylinder on the Hydraulic Trailer Brake Kit #AKUBRK-35 you were looking at uses the standard 3/8" x 24 Threads Per Inch brake line fittings. I included a video of the Kit #AKUBRK-35 for you to take a look at.

view full answer...

Answer 6

The Demco Hydraulic Brake Actuator part #DM72VR is a great option to replace an Atwood 82543. That said, it does not come with any sort of reverse lockout feature therefore in order to reverse without the brakes locking up you will either need to…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Self-Tapping Screws to Install Cruiser Accessories License Plate Mounting Plate

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching