Mounting Bracket Option for Titan Brake Rite # T4813102

Question

Question:

What are the mounting options for Titan BrakeRite EHB Electric-Hydraulic Actuator for Disc Brakes - # T4813100, I will be mounting it to the A frame box section with no access to the inside of the box, is a separate mounting plate required or is it supplied with a mounting plate.

asked by: Andrew H

0

Expert Reply:

We offer two mounting plates for the Titan Electric Over Hydraulic Actuators like the part # T4813102. We have the angle mounting bracket part # T4821800 and the flat plate part # T4821900.

I attached a picture that shows the bracket used to install an actuator as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went to our warehouse and measured one of the #T4821800 angled mounting brackets for you. The longer leg of the bracket measures 6.50 inches x 4 inches. The carriage bolt holes have a distance of 3.50 inches center-to-center. The shorter leg…

view full answer...

Answer 2

The difference is the material the Bearing Buddy is made from. The part #BB2047SS is made from stainless steel and the #BB2047 is chrome plated steel. Stainless will hold up to corrosion much better.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...