Stainless Steel Locking Hitch Pin Recommendation for 2016 Ford F-250

Question

Question:

I am looking for a stainless steel, lockack hitch pin for my 2016 Ford F-250. The outside diameter of the reciever tube is right at 2 1/2. Will the pins you show with a usable length of 21/2inch work?

asked by: Keith A

0

Expert Reply:

We have the Trailer Hitch lock part # e98882 which is a stainless hitch lock that would work well for you. This lock fits hitches that are up to 2-5/8 inches wide measured from the outside.

expert reply by: Jameson C

0

Answer 1

It sounds like you want to use the hitch lock, like #e98882, in place of a regular hitch pin. Yes, you can absolutely use the lock instead of a hitch pin and it will work great to safely transport the trailer and boat. The hitch lock does not have an…

view full answer...

Answer 2

When you order our etrailer.com locks part #e98882, enter the quantity of the locks you want and then select "Keyed Alike" from the drop down menu and we will send you as many as you need and they will all use the same key. I attached a…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 9

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 10

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Stainless Steel Locking Hitch Pin Recommendation for 2016 Ford F-250

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching