How are Trailer Fenders CE18041ATB Normally Installed on Trailer

Question

Question:

I just purchased a used enclosed trailer, and the fenders are missing. I would like to replace them:Single Axle Trailer Fender - Jeep Style - Aluminum Tread Plate - 13inch to 15inch Wheels. What would I need to mount them on this trailer? Thanks,

asked by: Todd G

1

Helpful Expert Reply:

The mounting brackets that are most commonly used with the Fender part # CE18041ATB that you referenced is the part # CE26098G-2 which would work well. I attached a review video for more info for you to check out as well.

expert reply by: Jameson C

1

Answer 1

On the CE Smith Fender Brackets #CE26098G-2 the long side of the bracket is 8-1/4 inches, the shorter side of the bracket is 6-1/2 inches, the bracket is an 1-1/2 inch in width, on the shorter side the holes of the bracket measure 4 inches, on the…

view full answer...

Answer 2

Based on your trailer tire size the Fulton Trailer Fenders part #F008585-2 would work very well for you. To see a chart with the fender dimensions see the attached picture.

view full answer...

Answer 3

We won't have an exact OEM fender part for your 1997 EZ-Loader boat trailer but we do offer a range of general purpose trailer fenders in plastic, aluminum and steel. I linked for you just the plastic fenders we have for 14-inch wheels and the…

view full answer...

Answer 4

Trailer fenders are sized according to the diameter of the trailer wheels. The Fulton #F008543 fenders you'd looked at are for a 13 inch wheel, so I'll assume that's what you have. If your wheel diameter is different, let me know. I'd…

view full answer...

Answer 5

It looks like the Single Axle Trailer Fenders #PF11X35W-2 that you referenced would be your best option. But before you order it check out the dimensions for it in the picture that I attached so that you can compare them to your trailer. For a Load…

view full answer...

Answer 6

From what I have found, the parts on the sheet you are talking about are no longer around. We do have some available options but they will not be identical to what you currently have. For bunk brackets for your Escort boat trailer, I recommend the CE…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 10

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...