Should Timbrens be Used with Air Bags in 2013 Toyota 4Runner

Question

Question:

Would it be a good idea to use both air bags and these bump stops?

asked by: Brian

0

Expert Reply:

The Timbrens part # TTORSEQ are a confirmed fit for your 2013 Toyota 4Runner. You would not need this kit plus an air bag kit. They both accomplish the same thing. If you ever were in a situation where both was needed your vehicle would be incredibly overloaded and you would have much bigger problems.

expert reply by: Jameson C

0

Answer 1

Installing a suspension enhancement system like the Timbren Vehicle Suspension, part #TTORSEQ will not affect the ride of your 2012 Toyota 4Runner when empty. The system is designed to help the ride when a heavy load is placed in your vehicle. It…

view full answer...

Answer 2

After installing the Timbren Rear Suspension Enhancement System #TTORSEQ on your 2006 Toyota Sequoia, there will be approximately 1/2" to 1-1/2" of clearance between the spring and axle. The Timbrens are among the most popular of…

view full answer...

Answer 3

From what I found online it looks like your 2019 Toyota 4Runner has a towing capacity of 5,000 lbs like you mentioned. You'd need to keep the weight of the trailer under that and you'd be fine. Towing capacities for vehicles are…

view full answer...

Answer 4

The correct Timbren Rear Suspension Enhancement System for a 2014 Toyota 4Runner is part #TTORSEQ which has a 6,000 lb weight capacity. I checked with Timbren and this is the lowest rated option they have for this vehicle.

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 9

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Should Timbrens be Used with Air Bags in 2013 Toyota 4Runner

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching