Does the Latch of the Pro Series Adjustable-Channel Coupler Lock Open When Slid Open

Question

Question:

Does the latch lock back to hold the coupler in the open position?

asked by: Frank

0

Expert Reply:

Yes, it does slide back and lock into the open position. If you wanted to release the latch of the # PSA200S0303 so that you could jack your trailer up and off the hitch ball you wouldn't be required to hold the latch open the entire time.

expert reply by: Jameson C

0

Answer 1

Although it's intended to be bolted in place, the Demco #DM15349-52 coupler mount could certainly be welded instead. I've linked you to a product description video featuing the #DM15349-52 A-Frame coupler mount.

view full answer...

Answer 2

All of the A-frame couplers we carry are for the standard 50 degree A-frames. What you could do, since your A-frame is a lower angle, is have some steel spacers welded on to get to 50 degrees and then use a weld-on coupler. I have linked the weld-on…

view full answer...

Answer 3

The Demco 6-Hole Adjustable Channel Bracket - Weld On - 12" Tall - 21,000 lbs #DM66134 is the weld on option for your trailer. There isn't a complete kit we offer, but it sounds like you are seeking the Demco 50-Degree A-Frame Coupler…

view full answer...

Answer 4

The Demco #DM15349-52 does not include mounting hardware. Demco recommends using grade 5 bolts, and the holes in the coupler are 5/8 inches in diameter. If you click the provided link, you can see a product demonstration video featuring the…

view full answer...

Answer 5

The best option we can offer you to secure the Sleeve-Lock Trailer Coupler part #CTA-196 is with a wraparound style trailer coupler lock, the Fastway Universal Trailer Coupler Lock part #FA86-0015-316 is what I recommend. I don't really have any…

view full answer...

Answer 6

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The important factors to consider is that your truck has an overall gooseneck/fifth wheel trailer towing capacity of 18,500 lbs and the max the trailer you are looking at could weigh is 16,900 lbs if loaded to it's capacity. So what that means is…

view full answer...

Answer 12

Yes, the Air Lift LoadLifter 5000 Air Helper Springs #AL57341 will fit your 2024 Chevrolet Silverado 2500 double cab with the Duramax diesel engine and factory puck system. We installed the upgraded Springs #AL88341 on a similar 2022 which I have…

view full answer...

Does the Latch of the Pro Series Adjustable-Channel Coupler Lock Open When Slid Open

Product Page this Question was Asked From

Continue Researching