Does Curt Adapter C57003 Fit 2011 BMW X5

Question

Question:

Will this adapter work on a 2011 BMW X5?

asked by: Pat

0

Expert Reply:

Yes, the adapter part # C57003 will fix any bulb out error codes on the dash of your vehicle caused by trying to tow a trailer with LED lights.

expert reply by: Jameson C

0

Answer 1

Since there is no standard set of bearings for a trailer you will have to do one of two things. You can pull a wheel and hub and check the bearings you have on one spindle. The numbers will typically be found stamped on the side of the bearings as…

view full answer...

Answer 2

We aren't able to determine which bearings your trailer has just by the make and model of the trailer. You'll need to pull the hubs and check the bearing numbers or measure the spindles where the bearings sit. Then you can use that to…

view full answer...

Answer 3

I looked through all of the replacement lenses that we have and none are a match for what you are looking for. I wish I had better news for you.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Does Curt Adapter C57003 Fit 2011 BMW X5

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching