Does Valterra City Water Inlet and Lockable Hatch Have A Check Valve

Question

Question:

I would like to get a new hatch door and assembly for filling by gravity and by hose, but I need to know if there is a check valve in the assembly, as it is needed to prevent water from leaking out when using the pump system for dry camping. Can you tell me if this includes a check valve?

asked by: Rob

1

Helpful Expert Reply:

The Valterra City Water Inlet and Lockable Hatch, part # A01-2000VP does have a check valve.

I have attached a photo of the fitting with the cap off and have an arrow that is showing where the check valve is in the unit. It is behind the red washer and screen.

expert reply by: Jeffrey L

1

click to enlarge

Answer 1

The correct Camco anode rod for your Suburban SW10DE water heater is part #CAM11563. You can confirm beforehand simply by comparing dimensions. This aluminum rod measures 3/4-inch diameter and 9-1/2-inches long. Aluminum anodes will tend not to…

view full answer...

Answer 2

Since the gravity fill and city water inlets usually have a hose connected behind them you should be able to swap out your current hatch for the Valterra #A01-2000VP without a problem. I recommend taking your current hatch off to check that you…

view full answer...

Answer 3

We have great options for RV city water inlets like the part #372160-85-A-3PA for a black inlet or part #37262145 for white.

view full answer...

Answer 4

There isn't a way to determine if you need the FPT like #37262155 or the MPT #37262145 without having you check and see. We don't have a way to look up that info prior.

view full answer...

Answer 5

The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver #3371809055 is designed or flatbeds and flatbed dump trucks. While it is ready to mount on Ford trucks, there is some drilling required for GM trucks. This hitch is a…

view full answer...

Answer 6

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 7

Yes, this is the replacement part you are looking for. I pulled the Camco Cam Lock - Straight or Offset - Thumb Operated, #CAM44323, from our warehouse to measure it for you. It has a threaded depth of 7/8 of an inch on the lock cylinder with the…

view full answer...

Answer 8

The Atwood #AT3308046006 cover that you selected will likely work just fine. I contacted the manufacturer and they did not have your model 600315.321 so I can't spec out the exact one. There may be another sticker on your unit ending in .331 or…

view full answer...

Answer 9

The mounting bracket of the #AS04 is 25 inches wide. The step width is 18 inches.

view full answer...

Answer 10

The Camco Olympian Wave 3 Catalytic Safety Heater for Small RVs #CAM57331 can heat a larger area (120 square feet) compared to the Little Buddy Heater which claims 95 square feet, has a built in automatic Piezo-electric spark starter which will last…

view full answer...

Answer 11

Thank you for the photo, it was very helpful, and I can confirm that your current B&B city water inlet can be directly replaced with an option from JR Products: - White: RV City Water Inlet with Brass Check Valve - 1/2" MPT #372160-85-A-26A…

view full answer...

Does Valterra City Water Inlet and Lockable Hatch Have A Check Valve

Product Page this Question was Asked From

Continue Researching