Availability of Black Valterra City Water Inlet Kit

Question

Question:

Is it available in black?

asked by: Tim B

0

Expert Reply:

Yes, for a black version of the # A01-2001VP you would want the part # A01-2001BKVP.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 4

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 5

You have a good eye as the black tubing sections are plastic for the Camco Gen-Turi RV Generator Exhaust System #CAM44461. It's just the curved pipe section that is made out of stainless steel.

view full answer...

Answer 6

Yes, for the white version of the MaxxFan Deluxe Roof Vent with 12 volt fan, thermostat, remote and powered lift we have the part #MA00-07000K which is exactly what you need.

view full answer...

Answer 7

You are going to need a kit like the Bulldog Winch Rear Wiring Kit #BDW20207 to carry enough power to run a winch on your trailer. The Redarc MC4 Output Cable #RED48VR is much to thin to carry the amount of power needed to run your winch and would…

view full answer...

Answer 8

The cutout dimensions for the Valterra City Water Inlet #A01-2001VP need to be 5-1/2" Wide x 3-1/2" High. It states this on the back of the packaging. However, the raised section in the middle at the back measures about 5-3/4" x…

view full answer...

Answer 9

25-1/8 inch would be perfect as a leaf spring replacement for what you have. So since your axle is a 6k axle the part #e47SR would be a great solution

view full answer...

Answer 10

It's hard to see in your picture but is the hanger open on the one side which allows the spring to slide out to the side? It shouldn't be open like that. If you need a replacement hanger we have the #115706S for if you have a 1-3/4 inch wide…

view full answer...

Answer 11

There will be different dimensions between the hangers. From front to back your hangers for that 20-3/8 inch spring like #e84SR will be 24-3/4 on center then 29 inches on center and finally 24-3/4 inches on center. This will put each of the 3 axles…

view full answer...

Answer 12

It is definitely not recommended to add different size wheels to one of your axles on your triple axle trailer. There is likely a miscalculation in axle spacing that is causing that third axle to sit off the ground. That definitely is not ideal and…

view full answer...

Availability of Black Valterra City Water Inlet Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching