Blue Ox Weight Distribution for an 8,700 Pound Travel Trailer

Question

Question:

My camper weight is 8700 lb loaded what size spring bars do I need on blue ox weight distribution 1000 lb bars.

asked by: Horace N

0

Expert Reply:

To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind the rear axle of the tow vehicle.

Trailer tongue weight alone is usually 10 to 15 percent of the gross trailer weight. So on a trailer that weighs 8,700 pounds that would be a tongue weight of 870 to 1,305 pounds. Based on this a 1,000 pound tongue weight capacity system may not be rated properly for the trailer.

If the total tongue ends up being between 1,000 and 1,500 pounds then I recommend Blue Ox Sway Pro system # BXW1506. But if it ends up being between 750 and 1,000 pounds # BXW1000 is the way to go. For either system you would need to add a ball, # C40086 for a 2-5/16 inch ball. I have linked some helpful articles on weight distribution and determining tongue weight for you.

expert reply by: Michael H

0

Answer 1

Using a Weight Distribution (WD) system that is rated too high or too low is never a good thing. Too high and your ride will be very stiff but too low and you won't see any benefit from it. Luckily we have a solution for you that does not require…

view full answer...

Answer 2

The first thing I'd recommend doing is to verify the trailer's as-towed tongue weight. I've linked you to a help article that shows a few ways to do this. Weight distribution set-ups will typically have a range of tongue weights for which…

view full answer...

Answer 3

I can help you get set up with all the right equipment for towing a travel trailer with your 1999 Ford Super Duty. A weight distribution system is recommended if the gross vehicle weight (GVW) of the trailer is more than 50 percent of the GVW of your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...