Does Wesbar Adapter WG54006-046 Use Standard Wire Colors for Trailer Wiring

Question

Question:

In the video on the WesBarg WG54006-046 7pin connector you state to be sure to test each wire and not rely on wire color. Do you know how the above referenced wiring harness is coded using the picture you provided? Is it the same or different? Do you have a Wes Barg schematic showing how the wire colors are placed in the head? I dont need additional headaches Thank You,

asked by: Ham D

0

Expert Reply:

The # WG54006-046 that you referenced does follow the color code chart that you attached a picture of.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The diagram you attached shows a 7-way wired up in what is considered the "traditional way." If you check out the chart I attached you will see the three ways (really only 2), that a 7-way can be wired. The Featherlite is wired up like the…

view full answer...

Answer 2

The wires of the connector on the part #WG54006-046 are sealed and there isn't a way to remove them. If you check out the diagram I attached, you can see how the pins of the connector are organized.

view full answer...

Answer 3

First thing I would do is test the 7-way at the rear of your 2009 Ford F150 for proper function with a circuit tester like our part #PTW2993. This will determine if the problem is on the truck or the trailer. Check out the video I attached to see how…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Does Wesbar Adapter WG54006-046 Use Standard Wire Colors for Trailer Wiring

Product Page this Question was Asked From

Continue Researching