Bayonet Fitting Cap Recommendation for 3 inch RV Sewer Pipe

Question

Question:

Hello, is this a bayonet tab style cap? Like this on at the attached photo? Regards

asked by: Josef

0

Expert Reply:

What you are looking for is the part # T1020-3VP which uses the 3 inch bayonet style fitting for a cap. The part # A0120SVP is for a smaller pipe diameter.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Valterra Water Inlet Cap and Strap for RVs - White - Gravity Fill #A0120SVP has an inner diameter between tabs of 1.5 inches. and inside diameter without tabs of 1.64 inches. The outer diameter is 1.96 inches. I've attached a photo to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 7

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 8

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...

Answer 9

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 10

To add a in-bed 7-way to your 2024 Chevy Silverado 2500 to make towing with a 5th wheel easier, I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long item #C58FV. This harness puts a 4-way and 7-way…

view full answer...

Answer 11

Hi Eric; the Curt Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger #C52044 will work for your triple axle Kaufmann trailer. This is designed for 1 to 3 axle trailers with electric brakes so triple axle isn't a problem. As long as…

view full answer...

Answer 12

Each of the leaves on the Leaf Spring #e47SR are 3/8" so this will give the spring pack a height of 1-1/2". Here is a list of our U-Bolt Kits for a 3" axle. Redline #APUBR-9 Dexter #APUBR-8 CE Smith #CE23003

view full answer...