Comparison of Draw-Tite Trailer Hitch # 75726 and Curt Hitch # 13534 for a 2008 Toyota Highlander
Question:
Is the Draw-Tite trailer hitch and Curt hitch pretty much the same product for the 2008 Toyota Highlander? Can you comment on either to help in my decision? Thank very much.
asked by: Dan S
Expert Reply:
Both the Curt Trailer Hitch, # 13534, and the Draw-Tite Hitch, # 75726 for a 2008 Toyota Highlander will install in very much the same way. I have included installation instructions for both hitches below for comparison. I have also included video links showing installation of each hitch.
Although the Draw-Tite model has a higher capacity at 7500 lbs towing and 750 lbs tongue weight, you will still be limited by the vehicle manufacturers stated towing capacity, which is a maximum of 5000 lbs. Both hitches are Class III hitches with 2 inch receivers. Both hitches will take the same amount of estimated install time.
The Curt hitch cannot be used with a weight distribution system, but the Draw-Tite model is weight distribution compatible. Unless you were planning on using a weight distribution system, you could choose the less expensive Curt hitch and not feel that you sacrificed anything.
Neither the Curt nor Draw-Tite hitch comes with the wiring harness, a ball mount, pin and clip, or a ball. For trailer wiring, you will need Tow Ready Custom Fit Vehicle Wiring, # 118449. I have included a link to the installation details and a video installation of this harness below. The recommended ball mount is # C45010, and you can use ball # 19260 (1-7/8 inch diameter) or # 19247 (2 inch diameter). For a pin and clip you can use # PC3.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Q&A: Will the Draw-Tite Hitch # 75586 Fit With My 19 inch Spare Tire
- Article: My Trailer Hitch Doesn't Fit
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: 2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 44649
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 68149
- Video: Choosing the Right Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Adding Brakes to a Mobile Home Axle
- Article: Trailer Wiring Diagrams
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Shop: Brake Controller
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Search Results: dust cap
- Shop: Fifth Wheel Hitch
- Search Results: 25580
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Gooseneck Hitch
- Q&A: Recommended Lithium Battery Compatible Power Converter For Parallax 7355