Replacement Coupler Latch Repait Kit for Demco eZ-Latch Coupler

Question

Question:

Looking for the following part: ez latch coupler repair kit Part number 6008. I contacted Demco and I was told I could purchase it online but i cant find the part

asked by: Ryan M

0

Expert Reply:

The Latch Repair Kit for Demco eZ-Latch Channel Tongue Trailer Coupler # DM5817 is the repair kit we carry. It is the same as the 6008 kit except the handle is metal where the handle is a composite material in the 6008 kit.

expert reply by: Charles S

0

Answer 1

looking at all the options we have for 2-5/16 inch A-Frame Couplers, the one you're looking at #DM16680-52 seems to look the most similar. I don't see any coupler that will be a perfect replacement. The holes on our coupler seem smaller and…

view full answer...

Answer 2

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 5

The play you are feeling/hearing is most likely between the hitch ball and the latch of the coupler. If you look under the coupler you can see an adjustment bolt that uses an Allen wrench that will allow you to tighten the latch and get rid of the…

view full answer...

Answer 6

Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing. You need to know what channel size and the weight capacity you will need for…

view full answer...

Answer 7

The Repair Kit Fulton Wedge-Latch Cast Head Coupler, #F670801, is designed to fit the coupler #BD44125W0317 which does take a 2-5/16 inch ball.

view full answer...

Answer 8

I do have an option for you but latch repair kits are coupler specific and there are very few out there. Furthermore, the Lippert 2" Latch Coupler Repair Kit 678750 is no longer available and I know this isn't what you want to hear but the…

view full answer...

Answer 9

The difference in the Repair Kit for Fulton A-Frame Coupler 2-5/16" Ball with Wedge-Latch part #F640801 and the Repair Kit Fulton Wedge-Latch Cast Head Coupler part #F670801 is what couplers they fit. Part number F640801 is designed for use with…

view full answer...

Answer 10

We have a Fulton coupler repair kit with the part #F670801 that you'd want instead of the #CA-5100-RK which only fits the Ram brand of couplers.

view full answer...

Answer 11

Yes we do. The part number you are looking for is #DM5817 and is the correct latch repair kit for your Demco Channel Tongue Trailer Coupler #DM12662-97.

view full answer...

Answer 12

The CE Smith Single Axle Trailer Fender w/ Top and Side Steps - Black Plastic - 14" Wheels - Qty 1 #CE19504 is my recommendation for you. It is 43-1/8 inches long x 11 inches wide x 12-1/2 inches tall which will give you a skirt height of 11-1/2…

view full answer...

Replacement Coupler Latch Repait Kit for Demco eZ-Latch Coupler

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching