Will GMC Hitch Cover part # CR-007G Activate with Turn Signals

Question

Question:

Looking at the hitch light cover for my 2002 GMC Sonoma. Will it also work the turn signals

asked by: Gene

1

Helpful Expert Reply:

The # CR-007G that you referenced will only activate with the stop lights or hazard lights. It will not activate with the blinker circuits. The small black box you see in the wiring is a converter that allows that.

expert reply by: Jameson C

1

Answer 1

There are always new things added to trucks with sensors and such for safety and this is one of the most recent. The workaround for an LED hitch cover like #CR-007G would be to add a load resistor. Some adapters like #C35FR have load resistors…

view full answer...

Answer 2

In order to install the Chevrolet Bowtie LED Lighted Vehicle Emblem part #RP86618 on your 2012 Chevy Silverado, our installers recommend using the Hopkins 4-Pole Loop part #HM48145 along with two packs of the 22-18 Gauge Butt Connectors part…

view full answer...

Answer 3

The Brake Light Trailer Hitch Receiver Cover for 2" Trailer Hitches #CR-007, is working correctly. It will blink when the right turn signal is on. If you look at the 4-Way on the light, you will see that it has a white, brown, yellow, and green…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Will GMC Hitch Cover part # CR-007G Activate with Turn Signals

Continue Researching