Part Number for Dutton-Lainson Hand Winch

Question

Question:

I am looking for a winch for cable that ties my boat dock to land i am replacing a shelby 5405 .and had decided on a DL1402A. i did not find that model on your site, but the DL15303 appears similar. can you tell me the difference?

asked by: Ronald K

0

Expert Reply:

The product ID for the DL1402A is the Dutton-Lainson Hand Winch with TUFFPLATE is # DL15303.

expert reply by: Charles S

0

Answer 1

Hi Bob, The Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies - 3,500 lbs #AKUBRK-35 are not free-backing. So you would need to install a solenoid like the Demco #DM11993.

view full answer...

Answer 2

If you have hydraulic brake assemblies that are not free-backing hydraulic trailer brakes, then the 10" X 2-1/4" Hydraulic Brake Shoe/Lining (One Wheel), #BP04-120, are the shoes that you will need. One set of shoes will replace one brake…

view full answer...

Answer 3

We have several sets of replacement hydraulic brake shoes available (see link to the right). Without knowing what size and brand of brake shoes you currently have though it would be impossible for me to recommend a set that would be confirmed to fit.…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Demco surge brake actuators require a Reverse Lockout Solenoid #DM11993. They do not have the ability to use a reverse lockout key.

view full answer...

Answer 6

Our lightweight winches will range between approximately 7 and 8 lbs. I recommend taking a look at the Dutton-Lainson 1,400 lb winch, #DL15303. The Dutton-Lainson winch is the heavier winch between the two at approximately 8 lbs and comes with…

view full answer...

Answer 7

The distance from the front hole to the beginning of the slotted mounting hole on the bottom of the Jif winch part #315-W1800D is 3.5 inches and then the distance to the rear of the slotted hole is 5 inches so you'd be able to line up two of your…

view full answer...

Answer 8

The Dutton-Lainson Hand Winch part #DL15303 is the replacement that I recommend for your Shelby Hand Winch 5405. These winches both have the same 1,400 lb capacity and overall size. In regards to mounting, most hand winches now use a standard pattern…

view full answer...

Answer 9

Since the Demco Hydraulic Brake Actuator #DM8759812 is a DA91 actuator the Reverse Lockout Solenoid Kit #DM5837 will fit. I confirmed this with my contact at Demco.

view full answer...

Answer 10

I can tell you how to go about determining if the Demco Hydraulic Trailer Brake Actuator - Drum Brakes #DM72VR will fit, but we wouldn't know off-hand an actuator fit on a 1985 EZ-Loader boat trailer. Finding out is really simple though, as the…

view full answer...

Answer 11

It sounds like your reverse lockout solenoid is not working properly. You can use the Replacement Solenoid Valve for Titan Brake Actuators with Reverse Lockouts #T4748800 or the slightly better designed Demco #DM5837. You will wire one side of the…

view full answer...

Answer 12

You can add a Manual Reverse Lockout Kit #DM5939 or Electric Reverse Lockout Solenoid Kit #DM5837 to the Demco Hydraulic Brake Actuator #DM8509612 to get the DA91 surge coupler with a reverse lockout.

view full answer...