Eliminating Wobble and Movement in a Yakima Trailer Hitch Mount Bike Rack
Question:
I have 2 inch receiver and 2 inch bike rack. There is way too much sway when rack is placed in receiver. Bikes bounce up and down and side to side when driving. I measured the receiver and the hitch tongue and they are both 2 inches. What can I do to remedy this?
asked by: Carl
Expert Reply:
You can use an anti-rattle device such as # SHP2082 as long as the shank on the bike rack is hollow. If it is not hollow then use anti-rattle device # MPG908. I have included a link to a video review of device # MPG908 for you.
It is also possible that inside the shank of your Yakima bike rack there is a weld nut that accepts a threaded hitch pin. To determine which pin will fit I would need to know the model of the bike rack.
Products Referenced in This Question
Malone Anti-Rattle HitchLock System
- Hitch Anti-Rattle
- Standard Anti-Rattle
- Universal
- Fits 2 Inch Hitch
- Clamp Style
- Accessory Anti-Rattle
- Malone
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Malone Anti-Rattle HitchLock System
- Shop: Roof Rack
- Shop: Landing Pad 1 for Yakima SkyLine and Control Towers - Qty 2
- Search Results: yakima landing pad 1
- Shop: Replacement 2" Anti-Rattle Hitch Bolt Assembly for Yakima Bike Racks and DryDock Load Assist
- Shop: SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4
- Shop: Yakima HD Crossbar - Aluminum - 60" Long - Qty 1
- Shop: Yakima LongArm Truck Bed Load Extender - 2" Hitches - Aluminum - 300 lbs
- Shop: Replacement Anti-Rattle Hitch Bolt for Yakima BigHorn, FlipSide, DoubleDown, and SwingDaddy Racks
- Search Results: yakima skyline tower
- Search Results: yakima hd bar
- Q&A: Yakima Crossbar Setup For Retrax Pro XR Tonneau Cover
- Q&A: How To Mount Yakima Towers In Retrax Tonneau Cover Tracks
- Q&A: Is the Mounting Hardware for the Landing Pads for Yakima Control Towers Part # Y00221 Included
- Q&A: What is the Difference Between Yakima Landing Pads 1 and 4
- Q&A: Recommended Tie Downs For Yakima Tracks That Use Yakima A Anchors Y8810074
- Q&A: Yakima Towers Needed to Mount to Landing Pad 1 on Track System
- Q&A: Troubleshooting RetraxONE MX Cover Leaking at Tailgate on a 2016 Ford F-150 with 5-1/2 Bed
- Video: Review of Yakima Replacement Top Channel Crossbar Infill For HD Style Crossbars - Y33KV
- Shop: Trailer Wiring
- Video: Malone Anti-Rattle HitchLock System Review
- Video: Yakima EXO System Cargo Carrier and Enclosed Cargo Carrier Review - 2017 Toyota RAV4
- Video: Review of Gen-Y Hitch Hitch Anti-Rattle - Anti-Rattle Clamp 2 Inch Hitch Receiver - GY88XR
- Video: Thule Overcast Roof Rack Mount Awning Review
- Video: Yakima HoldUp Bike Carrier Nut Retainer and Nut Review
- Video: Yakima Bike Racks 2 Inch Shank Adapter Replacement Review
- Shop: Trailer Hitch
- Shop: Suspension Enhancement
- Search Results: hitch clamp
- Shop: Truck Bed Extender
Jojo
4/12/2024
Hi Michael, I have the same issue, can you explain more about the "weld nut that accepts a threaded hitch pin"? Specifically I had a 2 inch receiver "EcoHitch Invisi Trailer Hitch Receiver - Custom Fit - Class III - 2" and a 2 inch bike rack "Yakima, RidgeBack 4 Hitch Mount". Thanks in advance.