Anti-Rattle Hitch Bolt for Yakima FullSwing Hitch Bike Rack

Question

Question:

I am looking fow a hitch bolt for Yakima 2004 Fullswing. Nothing shows up in a search of your website. Similar products show for Swingdaddy, et al , but not for Fullswing. Which part should I buy for 2004 Fullswing?

asked by: Kevin C

0

Expert Reply:

For the now-discontinued Yakima FullSwing hitch bike rack 8002403 you can use anti-rattle mounting hardware kit # Y8780022. This includes a hitch bolt, nut, clip and anti-rattle insert.

expert reply by: Adam R

0

Answer 1

We have actually seen this issue before. The 2" receivers on Toyota trucks and SUVs have a slightly larger diameter on the outside of the receiver tube than most typical 2 inch hitches. This is partially the powder coating, but the steel itself…

view full answer...

Answer 2

Yes! We do have those parts for your Yakima SwingBase #Y34VR. The replacement parts you need the Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR (Yakima part 8880953) and the Replacement Hitch Bolt Threaded Insert…

view full answer...

Answer 3

I measured the bolt that is included in the Yakima Replacement parts kit #Y8780022 and found it has the following dimensions: Overall Length 4-5/8 Hex Head Size 13/16 Thread diameter 1/2 Length of Thread 2-1/2 I prepared a photo with these dimensions…

view full answer...

Answer 4

I checked with Yakima and for the Exo Swingbase part #Y34VR the correct replacement hitch pin bolt is the part #Y52FR.

view full answer...

Answer 5

The Yakima Threaded Hitch Bolts #Y8880131 have a 1/2" -13 thread pitch. I do not see we have any M20 threaded hitch pins or bolts as this is larger than a 3/4" bolt. Most hitch pins are 1/2" or 5/8" in diameter.

view full answer...

Answer 6

I went out to the warehouse and pulled Replacement Hitch Bolt and Clip #Y8890200 to measure it. From under the bolt head to the end of the pin it measures 4-1/4 inches. And to the center of where the clip would go it measures 3-9/16 inches. If it is…

view full answer...

Answer 7

If I understood your question correctly it sounds like you are asking about the diameter of the very end of the Replacement Hitch Bolt #Y8890200. I went and pulled this from our warehouse to measure it and found it to be 3/8 of an inch. If you are…

view full answer...

Answer 8

I spoke with my contact at Yakima regarding your older model 4-bike rack. He said that based on your description, the correct replacement hitch bolt is the part #Y8890200. He stated that this bolt was actually re-designed with the wider Toyota hitch…

view full answer...

Answer 9

Both of the bolts that come with the Yakima Hitch Pin Set #Y8880131 are 1/2 inch diameter with 13 threads per inch. One is 4.279” long and the other is 2.598” long.

view full answer...

Answer 10

For a replacement hitch pin for your Yakima Stickup you would want the part #Y8880131. This comes with both sizes but is the same price basically as the individual hitch pins we offer for other racks so it would still be ideal for you.

view full answer...

Answer 11

For a replacement hitch pin for your Yakima Stickup you would want the part #Y8880131.

view full answer...

Answer 12

We may have the correct replacement hitch bolt for you, but they are specific to both manufacturers as well as racks, so the Saris hitch bolt you mentioned won't work for your Yakima 2-bike rack. There are a number of options for you, and to get…

view full answer...

Anti-Rattle Hitch Bolt for Yakima FullSwing Hitch Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching