Diameter of the End of the Replacement Hitch Bolt # Y8890200

Question

Question:

Good Afternoon! What is the actual width of the flat pin area?? I was hoping it was 3/4 inch. Thanks,

asked by: Jodi

0

Expert Reply:

If I understood your question correctly it sounds like you are asking about the diameter of the very end of the Replacement Hitch Bolt # Y8890200. I went and pulled this from our warehouse to measure it and found it to be 3/8 of an inch.

If you are asking about the length of the non threaded portion of the pin minus the tip it is 3/4 of an inch.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes! We do have those parts for your Yakima SwingBase #Y34VR. The replacement parts you need the Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR (Yakima part 8880953) and the Replacement Hitch Bolt Threaded Insert…

view full answer...

Answer 2

Thanks for the picture of hitch pin, but what was really helpful was actually the set of instructions you have in the background. Based on that you have the first version of the BigHorn which was made around 2001 and the correct hitch pin…

view full answer...

Answer 3

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 4

I checked with Yakima and for the Exo Swingbase part #Y34VR the correct replacement hitch pin bolt is the part #Y52FR.

view full answer...

Answer 5

The Quick Hitch Bolt has been discontinued so you will want the Replacement Hitch Bolt and Clip #Y8890200. The mounting hardware replacement kit includes a hitch bolt, washer and clip for Yakima hitch-mounted bike carriers for 2" hitches. I…

view full answer...

Answer 6

If you wish to convert your Yakima HoldUp Bike Rack for use in a 2-inch hitch you will use the Replacement Tongue #8880580. With this you will need a longer hitch pin, part #Y8890200.

view full answer...

Answer 7

I measured the Replacement Nut Retainer and Nut #Y90254 and have an included diagram with everything you will need. I will also mention that this is designed for use with the Yakima HoldUp bike rack with a 2" shank, like the #Y02443. The…

view full answer...

Answer 8

I spoke with my contact at Yakima regarding the correct replacement hardware for your Yakima HoldUp Bike Rack. He stated that since you have the silver/gray model, both the Replacement Mounting Hardware #Y8890176 and #Y8880129 will actually work.…

view full answer...

Answer 9

We may have the correct replacement hitch bolt for you, but they are specific to both manufacturers as well as racks, so the Saris hitch bolt you mentioned won't work for your Yakima 2-bike rack. There are a number of options for you, and to get…

view full answer...

Answer 10

The correct replacement threaded hitch pin for the Yakima BuckHorn 4 Bike Rack is the Replacement Hitch Bolt and Clip for Yakima HoldUp and BigHorn Bike Carriers part #Y8890200.

view full answer...

Answer 11

The Yakima Threaded Hitch Bolts #Y8880131 have a 1/2" -13 thread pitch. I do not see we have any M20 threaded hitch pins or bolts as this is larger than a 3/4" bolt. Most hitch pins are 1/2" or 5/8" in diameter.

view full answer...

Answer 12

I went out to the warehouse and pulled Replacement Hitch Bolt and Clip #Y8890200 to measure it. From under the bolt head to the end of the pin it measures 4-1/4 inches. And to the center of where the clip would go it measures 3-9/16 inches. If it is…

view full answer...

Diameter of the End of the Replacement Hitch Bolt # Y8890200

Product Page this Question was Asked From

Continue Researching