Plug Or Cover For 4 Inch Hole In The Bed Of My 2010 Ford Super Duty Truck

Question

Question:

I am looking for something similar to this # RP30136 however the hole I have is 4 inches internally. is there a puck that fits this? I am unsure of what hitch or whatever was there before.

asked by: Matt

0

Expert Reply:

We don't have a puck cover like # RP30136 that has a 4 inch internal dimension. Most underbed gooseneck systems required a 4 inch hole cut for the unit, but that included the outside ring of the system and sometimes trim as well as the hole for the ball. It sounds like there was an underbed gooseneck system installed. For instance, the 2010 Ford F-250 and F-350 Super Duty B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs, # BWGNRK1108, required a 4 inch hole. I've attached an installation of this system for you.

My recommendation is to install a replacement hitch or have a professional welder patch your bed.

expert reply by: Jason S

0

Answer 1

If your gooseneck ball uses a square shank that measures 2 inches by 2 inches, Hitch Cover #DT7010 you referenced might work for you, but typically the square shank would be larger than 2 inches square, so the cover you referred to would likely be…

view full answer...

Answer 2

Installing ta Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like the #325-GH-8045 would not void the warranty of your camper, and Gen-Y makes some of the most durable parts on the market. I really like this as an alternative to…

view full answer...

Answer 3

The Curt Ball and Safety Chain Loop Kit for Chevy, Ford, GM, and Nissan Underbed Gooseneck Trailer Hitch #C60692 does not need to be greased unless the mechanism isn't working properly. A spray penetrating spray grease works well,…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Steve, so between the Curt #C16265 and the Pullrite #PUL36ZR I'd go wit the Curt but not the Q25. I'd go with the A25 #C24FR, which is basically the same thing as the Q25 but does not require the #C88KR adapter. Only the Curt is going to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Plug Or Cover For 4 Inch Hole In The Bed Of My 2010 Ford Super Duty Truck

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching