Speed of Travel for the Trailer Valet XL Trailer Dolly with Chain Drive # TVXL2

Question

Question:

What are the approximate speeds this will travel at on a flat surface pulling 4500lbs?

asked by: Stefan M

0

Expert Reply:

The Trailer Valet XL Trailer Dolly with Chain Drive # TVXL2 does not move very quickly. If you watch the beginning of the video link I attached you can see that it moves at a very slow walking pace basically. But that also depends on how fast you are cranking it.

expert reply by: Jameson C

0

Answer 1

The Trailer Valet XL Trailer Dolly with Chain Drive - 2-5/16" Hitch Ball - 1,000 lbs TW #TVXL25 or the 2 inch ball #TVXL2 have two different drive gears to make it easier to go up an incline or to overcome a lip in the concrete as you described.…

view full answer...

Answer 2

I looked up the Shelby 5133 coupler and it said it uses a 2 inch hitch ball. You also need to get the right ball shank diameter and ball shank length. The ball mount determines the diameter and length. If you measure the hole size diameter in your…

view full answer...

Answer 3

The instruction manual for the Trailer Valet XL Trailer Dolly with Chain Drive item #TVXL2 states not to use the dolly on any flat or paved incline or decline that is steeper than 10 degrees.

view full answer...

Answer 4

I would first double check to make sure that everything is installed properly. The hitch ball that comes with the Trailer Valet XL #TVXL2 has a base that you spin to lock your unit to the coupler so that it sits straight. If you have an older version…

view full answer...

Answer 5

From the picture that you sent (thank you for that) and the way that you are describing that the Trailer Valet XL #TVXL2 is moving I would have to say that you might not be installing the Trailer Valet XL properly on your coupler. I have attached a…

view full answer...

Answer 6

Would a dolly possibly be easier to maneuver the trailer? Sounds like what you are really wanting to do is hand guide a trailer into a parking spot and were wanting a winch to help control it and guide it. For that type of application the Trailer…

view full answer...

Answer 7

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 8

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash. The…

view full answer...

Speed of Travel for the Trailer Valet XL Trailer Dolly with Chain Drive # TVXL2

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching