Grease Seal For Utility Trailer With Inner Bearing KL68149

Question

Question:

I need the inner seals seaks only, not bearings for my utility trailer. The inner bearing has number KL 68149 made in Hungary. Is this sufficient information to provide options for seals? Thanks in advance

asked by: Alan T

0

Expert Reply:

That KL68149 bearing number was enough to help me with seal. The seal you need is the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2 # RG06-050.

expert reply by: Jason S

0

Answer 1

Bearing Buddies do make it very easy to over fill hubs and blow out grease seals. The correct replacement seal you need based on your bearing and race number is RG06-050.

view full answer...

Answer 2

I have a replacement axle option for you, but based on the information I was able to find on your AL-KO 4400lb Axle #402268 it uses an older style of braking assembly that was discontinued when AL-KO was bought out by Dexter. If the brakes on your…

view full answer...

Answer 3

I've done some looking around online, and found that the #RG06-050 is the equivalent of the AL/KO 56886 or the Hayes #09103305. This is usually found on 3500 lb axles with the L68149 inner and L44649 outer bearings. I've linked you to…

view full answer...

Answer 4

If the number you found on the grease seal you pulled out of the hub was 473336 then that means the correct replacement seal is the part #RG06-050. This is commonly seen on the 3,500 lb axles but what also factors into this is that the 3,500 lb…

view full answer...

Answer 5

From the measurements provided in the photos, it looks like you have an inner bearing that has a 1.250 inch inner diameter and an outer bearing #LM11949, which has a .750 inch inner diameter. This leads me to believe you have some variation of…

view full answer...

Answer 6

I would be happy to recommend the parts needed to add electric brakes and new bearings on your 2010 Stehl ST80TD Tow Dolly, but first I will need you to confirm which bearings your spindle uses and if you already have a brake mounting flange…

view full answer...

Answer 7

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Grease Seal For Utility Trailer With Inner Bearing KL68149

Product Page this Question was Asked From

Continue Researching