Hardware Kit for Trailer Hitch Receiver on a 1993 Jeep Cherokee

Question

Question:

Do you guys sell bolt kit to bolt on a hitch for a 93 jeep cherokee? I.e. Bolts -nuts-washers-steel squares and bolt leader?

asked by: Robert

0

Expert Reply:

We do sell hardware kits for trailer hitch receivers. You'll use # RHK and provide the manufacturer and part number of the hitch receiver you already have.

expert reply by: Charles S

0

Answer 1

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel…

view full answer...

Answer 2

There are 3 hitches made for the 2003 Honda CRV. They each are designed differently and they each have different hardware kits. There are three Class III hitches, the Draw-Tite #75690, the Curt #13535, and the etrailer Hitch #e69AR. You can order…

view full answer...

Answer 3

To put your Curt Trailer Hitch Receiver #C13206 on your 2015 Subaru Outback, I recommend using the hardware kit #RHK which will get you all the parts that originally came with your trailer hitch so you can safely install it on your new vehicle. On…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Hardware Kit for Trailer Hitch Receiver on a 1993 Jeep Cherokee

Product Page this Question was Asked From

Continue Researching