Wheel Chock Axle Stabilizer Recommendation for Wheels 16 inches Apart

Question

Question:

I have a passport 31ft wheels 16in apart looking for stabilizer chocks? to prevent movement front to back. Any to cover that space? Most I see are up to 10 in? Thanks

asked by: Pastor B

0

Expert Reply:

We have the Super Grip Chock XL Wheel Stabilizer for Tandem-Axle Trailers # UF21-001094 which can fit wheel spaces of up to 17 inches. For a pair you would then want the part # UF21-001095.

expert reply by: Jameson C

0

Answer 1

In order to recommend a replacement gearbox, I'd need to know the manufacturer and model number of your existing landing gear. I'd try operating that leg independently of the gear box if possible, which will confirm the gear box as…

view full answer...

Answer 2

If you get the Out of Stroke error message on the Lippert Ground Control system, such as #LC358590, then that indicates that the jack has extended as far as it will go and cannot go any further. To clear the error you can extend all of the jacks in…

view full answer...

Answer 3

What you described is definitely a bad gear box on your Venture landing gear. So what you'll need is the replacement gear box part #LG-179015 and you'd be set! If you ever need to replace the motors too they are part number #LG-142178.

view full answer...

Answer 4

The 241845 actually comes back to the Replacement Heavy-Duty Landing Gear Jack Leg #LC241845 which is the replacement leg for the Ground Control 2.0 which does not have a gear repair kit available so you would need to replace the leg with a new…

view full answer...

Answer 5

There are a couple potential reasons why the back Lippert Power Jack #LC298707 on your trailer won't extend or retract even with the motor running. It's possible that it may have been over-extended or something internally has been stripped or…

view full answer...

Answer 6

The left front jack error code ("LF) you are getting on your Lippert Ground Control System like #LC675817 can be triggered by a few different things. The first, which it seems you may have already ruled out, is that the system is for whatever…

view full answer...

Answer 7

You'll want to replace the check valve with the part #P23415LFVP if the internal components of what you have now are coming out.

view full answer...

Answer 8

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 9

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 10

I'd go with the part #UF21-001091. It locks the tire of each axle so well to each other that the trailer would not roll at all if pushed while you were hitching up. I attached a review video for more info. If you wanted to be super cautious a…

view full answer...

Answer 11

I have a solution for you, but the Tow Smart locks like the TowSmart Trailer Coupler Lock - 1-7/8", 2", and 2-5/16" Couplers #3481213 cannot be keyed alike. For that reason, unless there is a number somewhere on the lock or key, the…

view full answer...

Answer 12

Your new 2018 Jayco trailer has a bottom mount or underslung coupler. For a lock that will work well, I recommend the Atwood AMPlock Underslung Coupler Lock #AT89006. This cast iron lock is designed specifically for underslung couplers and will help…

view full answer...