Draw Tite Hitch Fit Recommendation for 2016 Mercedes Sprinter 3500 with 144 inch Wheelbase

Question

Question:

75549 hi! Can you pls re confirm it will suit our mb sprinter 319 CDI, 2016, wheel base 3665 cm, 3,5 mt Yours

asked by: Kirill

0

Expert Reply:

I believe you meant to type 366.5 cm wheelbase as that would equal 144 inches which the Draw Tite hitch part # 75549 would be a fit for your 2016 Mercedes Sprinter if you didn't have the factory step bumper. If you did have the factory step bumper you would want the part # 75601.

expert reply by: Jameson C

0

Answer 1

For your 2022 Mercedes Sprinter 2500 that has a 170 inch wheelbase and the standard bumper the etrailer hitch part #e76AR is the highest capacity option available. It can tow a trailer up to 10,000 lb. We do not carry replacement leaf springs or step…

view full answer...

Answer 2

Yes the Draw Tite hitch part #75601 does attach to the outsides of the frame rails of your 2020 Mercedes Benz Sprinter 2500. You can see this in the install instructions diagram that I attached to this page.

view full answer...

Answer 3

The frames are different on cargo van and passenger van versions of the 2017 Mercedes-Benz Sprinter 2500, which is why the Curt Hitch 13388 won't fit. I did check with our manufacturers and the only option for a hitch that fits your '17…

view full answer...

Answer 4

The Draw Tite #75601 and the Curt #13358 that you referenced both are a fit for your 2017 Mercedes Benz Sprinter 2500. They have very similar ground clearance but the Curt has the slight edge as it seems to sit a bit higher. I attached a picture that…

view full answer...

Answer 5

There is one trailer hitch that you can potentially use on your 2019 Mercedes-Benz Sprinter 2500 passenger van with the factory step bumper, which is the Draw-Tite Trailer Hitch #75601. The only potential caveat is that this hitch will not fit if…

view full answer...

Answer 6

The trailer hitch we offer for your 2016 Mercedes-Benz Sprinter 2500 that sits the highest will be the Curt #C13388 which fits right under the rear bumper like the picture I attached. It will sit about 1-1/4 inch taller than the Draw Tite.

view full answer...

Answer 7

If your 2019 Mercedes-Benz Sprinter 2500 has a standard bumper without the step, the Draw-Tite #75549 is going to provide you with the most ground clearance at 15" from the bottom of the receiver tube to the ground. If your Sprinter has the…

view full answer...

Answer 8

We haven't installed Draw-Tite trailer hitch #75549 on a 2014 Sprinter 2500 but on the 2016 model year after the hitch was installed, see video, it measured 17-1/4 inches from the ground to the top of the receiver opening. So from the ground to…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...