Replacement Master Cylinder Recommendation for Titan Model 6 Drum Actuator T4079200

Question

Question:

Is the T4079200 coupler master cylinder rebuildable?

asked by: Derek

0

Expert Reply:

What would be the easiest solution would be to just replace the master cylinder of the part # T4079200. For that you would want the master cylinder part # T1777401.

expert reply by: Jameson C

0

Answer 1

The overall length of the Titan Model 6 actuator #T4079200 is right at 24 inches. I attached a review video for more info on the actuator as well.

view full answer...

Answer 2

On the linked page you can see all 12,500-lb-rated bolt-on drum brake surge couplers for 2-5/16-inch balls that will fit on a 3-inch straight trailer tongue. These are offered with or without drop, as with #T2478100 with 3-inches of drop and…

view full answer...

Answer 3

I will be happy to explain resetting the breakaway lever on the Titan Model 6 actuator, #T4747200. The manual states: Resetting the Break-away Lever: (Refer to the parts diagram in the instructions linked to the right). When the break-away lever…

view full answer...

Answer 4

Locking out a Titan Model 60 actuator like the part #T63FR that you referenced requires inserting the lock out tool into the into the slot right behind the portion of the coupler that inserts into the outer casing. I pointed out where in the…

view full answer...

Answer 5

It's a bit hard to tell based on the picture but it does look like you might have an older Titan Model 6 Brake Actuator like our 8K #T4079200. If this is the case then you can use the Replacement Shock #T1242600 to resolve the issues…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Replacement Master Cylinder Recommendation for Titan Model 6 Drum Actuator T4079200

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching