2 Prong Connector Recommendation for Clearance Light on Boat Trailer

Question

Question:

I was replacing a submersible clearance light on a boat trailer. The connector that connects to the clearance light is a 2 prong connector. The prongs broke and I am looking for replacement connector. 2 prong connector that connects to submersible clearance light. Thank You,

asked by: LUKE R

0

Expert Reply:

Based on what you described it sounds like you are looking for the part # A45CB which is a 2 prong connector designed for similar trailer clearance lights.

expert reply by: Jameson C

0

Answer 1

To install a side marker light like the Optronics #AL82AB on your 2014 Malibu you will need to ground the white wire and then connect the black wire to your running light circuit. This then installs on the mounting bracket #A91BOB which you will need…

view full answer...

Answer 2

The LED Trailer Light Kit for Trailers Over 80" Wide part #TL16RK comes with a trailer wiring harness that has both the vehicle side plug (three covered, one exposed pin) and the trailer side plug (three exposed, one covered). Therefore, it has…

view full answer...

Answer 3

The 4-way wiring harness that comes with the #TL16RK is 25 feet in length and while we don't have a version that comes with a longer harness you could pretty easily extend this 4 more feet with the #HM47114.

view full answer...

Answer 4

First, if you are switching to LED lights on the trailer, make sure to replace all of the incandescents with LEDs. Mixing the two styles can result in some of the lights not working and/or malfunctions. Clearance lights, LED or otherwise, that have 2…

view full answer...

Answer 5

Though we do recommend having a resistor on each LED light, we do have other options as well. Since you mentioned having a 7 Way connector, you could use a lamp out sensor adapter like the #20142 if the trailer is wired with a 7 Way plug or a #C35FR…

view full answer...

Answer 6

Absolutely, you can check just behind the rear tire on the driver's side of your 2019 Kia Sorento, on the outside of the frame rail. The factory connector, if present, will look like the one in the attached photo (B). Note that you will need to…

view full answer...

Answer 7

For your 2018 Hyundai Santa Fe with the factory tow package I recommend the Curt T-Connector Vehicle Wiring Harness #C56332. This particular harness features a higher amp rating than the other options available for your vehicle and Tekonsha is well…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...