3,500 lb Capacity Idler Hub Recommendation that Comes with Marine-Grade Grease

Question

Question:

Does or can this come greased with marine based grease?

asked by: Howard L

0

Expert Reply:

I have a solution for you, but the part # AKIHUB-545-35-K does not come with marine grade grease.

Instead you would want the part # CE13511 as it is essentially the same spec hub in terms of bolt pattern and what spindle it fits except it does come with marine-grade grease.

expert reply by: Jameson C

0

Answer 1

If the spindle is damaged, it'll need to be replaced. The #CE13511 CE Smith hub is compatible with a 3500 lb axle that uses an L68149 inner/L44649 outer wheel bearing and a 10-19 grease seal. For a spindle, you'll need a 3500 lb spindle, but…

view full answer...

Answer 2

The CE Smith Trailer Hub Assembly #CE13511 uses the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles #RG06-050; these are sold in pairs with that part number or you can the individual seal with part #58846.

view full answer...

Answer 3

Yes, the CE Smith Trailer Idler Hub Assembly #CE13511 is compatible with the spindles on your Trailstar boat trailer since it uses the same bearings #L68149 and #L44649. It will fit your wheels with the 5-on-4-1/2 bolt pattern. This spare hub kit…

view full answer...

Answer 4

Selecting a compatible hub requires matching a few factors, among these the bearings, which must match in order for the hub to fit on your spindles. You also need to match the wheel bolt pattern on the hub to that on your wheels and the weight rating…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

3,500 lb Capacity Idler Hub Recommendation that Comes with Marine-Grade Grease

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching