Can Trailer Valet XL Trailer Dolly # TVXL2 work on trailer with 550 lb Tongue Weights

Question

Question:

Im considering purchasing an RV primetime Avenger GVRW of just under 7500 lbs and tongue weight is 550 lbs Can the trailer valet xl handle this RV Safely? Thanks

asked by: Sean

0

Expert Reply:

The Trailer Valet XL part # TVXL2 that you referenced has a 1,000 lb tongue weight capacity so it would easily work with your trailer that has 550 lbs.

expert reply by: Jameson C

0

Answer 1

The lever/handle at the top of the Trailer Valet XL #TVXL2 is what is going to lock/unlock your wheels, where the crank on the side of the unit is what will get the wheels to move- you're not able to push and pull the Trailer Valet XL since…

view full answer...

Answer 2

While the Trailer Valet XL Trailer Dolly #TVXL25 does say it is intended for use on flat surfaces a slight incline or decline will not be a problem for this dolly. Trailer Valet has tested and allows for up to a 10% grade or 5.7 degrees of incline…

view full answer...

Answer 3

The Trailer Valet 5X, #STC-V211 is a jack that is mounted to your trailer with a bolt-on bracket and therefore, is designed to be used with just the one trailer to which it is attached. It does not come equipped with the ball base, so a ball cannot…

view full answer...

Answer 4

As long as the tongue weight of the trailer is around 10-15 percent of the total trailer weight the Trailer Valet XL Trailer Dolly #TVXL25 is going to work like it was designed for. It does decently on flat surfaces and inclines but if it's…

view full answer...

Answer 5

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 6

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 7

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 8

If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash. The…

view full answer...

Answer 9

I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have not…

view full answer...

Answer 10

The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your Tahoe…

view full answer...

Answer 11

I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part #LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch…

view full answer...

Answer 12

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Can Trailer Valet XL Trailer Dolly # TVXL2 work on trailer with 550 lb Tongue Weights

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching