Replacement Bulldog Jack Recommendation to Fit Trailer with Round Pipe Mount
Question:
We own a 1998 boat trailer with a Bulldog jack. The base swivel plate is welded to the trailer frame. I need to replace this old jack but cant locate a replacement that would utilize the old welded plate. Any suggestions?
asked by: Charlie R
Expert Reply:
The Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 7,000 lbs, item # BD198250, has a male pipe on the jack and a female receiver that welds to the trailer. This female receiver has an inside diameter of just over 2-1/2 inches to fit on the 2-1/2 inch male pipe welded to the jack. This jack utilizes a 5/8 inch pin to secure the jack to the trailer.
For a jack with a 2 inch outside diameter male receiver that welds to the trailer frame and has a capacity of 5,000 pounds, we have the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 5,000 lbs, item # BD178203. This is the largest capacity jack we have with a 2 inch round mounting pipe. This jack also uses a 5/8 inch pin to secure the jack to the trailer.
You would need to compare the dimensions of the pipe on your trailer to see which would work.
Products Referenced in This Question
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 7,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 6001 - 7000 lbs
- Sidewind Jack
- Swivel Jack
- 15 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Product Page this Question was Asked From
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- Swivel Jack
- 15 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Continue Researching
- Video: etrailer Camper Jack - Stabilizer Jack - SJ-R208 Review
- Video: Pro Series Round Pipe-Mount Swivel Jack Reveiw PS1401420303
- Video: Fulton Camper Jack - Stabilizer Jack - FSJ1-SJ2 Review
- Video: Pro Series Trailer Jack - Side Frame Mount Jack - PS1401420303 Review
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs
- Shop: Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
- Shop: Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs - Qty 1
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 20" Leg
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 7,000 lbs
- Shop: Americana Trailer Wheel Lug Nut - Chrome Plated - 1/2"-20
- Search Results: lug nuts
- Search Results: 1/2 20 lug nuts
- Shop: Replacement Mirrors
- Search Results: telescoping stabilizer jack
- Q&A: Recommended Flatbed Cargo Trailer Stabilizer Leg for Rear of Trailer
- Q&A: What Diameter Tube Does Pro Series Pipe Mount 5k Trailer Swivel Jack Mount To
- Q&A: Pipe Mount Trailer Jack Recommendation for Utility Trailer
- Q&A: Weld-On Jack Pipe Mount Recommendation for a12,000 lb Equipment Trailer
- Q&A: Is 5,000 lb Bulldog Topwind Jack Stronger or Easier to Use than Bulldog Sidewind Jack
- Shop: Trailer Hitch
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Video: B and W Hitch Ball - Trailer Hitch Ball - BWHB94005 Review
- Search Results: 68149
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Article: Trailer Tire Sizing
- Shop: Trailer Wiring
- Shop: Fifth Wheel Hitch