Dimensions of Redline Replacement Exterior Pop-Up Roof Vent

Question

Question:

Is the 8inch width the actual width of the part or is it the width of the gasket that goes under the vent? I have a 2014 Ford E-250 van I want to install these on the roof. The raised panels on the top of the van look to be just 8inch wide.

asked by: Lance C

0

Expert Reply:

The entire length and width of the Redline Replacement Exterior Pop-up Roof Vent # 9106 are 13-1/2 by 8 inches. The opening measures 9-1/2 by 4 inches. I've attached a picture that may make it more clear.

expert reply by: Charles S

0

click to enlarge

Answer 1

A cut out template is not included with the Replacement Exterior Pop-Up Roof Vent #9106. So you will need to do some measuring before installation, and it will install in an opening of roughly 11-1/8" long x 5-1/2" wide. I have…

view full answer...

Answer 2

The closest that we have for your application is the Replacement Exterior Pop-Up Roof Vent - Steel - 13-1/2" x 8" - Black #9106 which fits a rough opening size of 11-1/8" long x 5-1/2" wide. It sounds like you…

view full answer...

Answer 3

The leg length or the depth that the garnish part #2756 has is right at 2 inches. From the picture you submitted it looks like you installed the roof vent part #9106 with the mounting flange on the inside of the trailer. The vent should be…

view full answer...

Answer 4

I don't see any reason you couldn't use the Redline 2-Way Pop-Up Roof Vent with Garnish for Enclosed Trailers #9106-2756 in the metal window panels of your Ford Transit Connect. People install these on similar surfaces pretty…

view full answer...

Answer 5

You are right that a huge compressor can really be a pain and we have exactly what you need with a portable system, the Bulldog Winch Portable Air Compressor #BDW41003 which only measures about 10-1/2" long x 5-1/2" wide x…

view full answer...

Answer 6

The Redline 2-Way Pop-Up Roof Vent, part #9106-2756 adjusts in steps from fully closed to keep rain or air out, to fully open to let fresh air in. This vent can be installed with the vent facing either direction and being able to open the vent…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover,…

view full answer...

Answer 10

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 11

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this…

view full answer...

Answer 12

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...