Replacement Amber Mini Trailer Clearance Light For Wesbar 3395

Question

Question:

Im looking for a replacement for a trailer light. It is Wesbar 3395 Amber. Do you have a product that will work? Thank you for the help.

asked by: Scott

0

Expert Reply:

We have just what you are looking for.

The replacement clearance light we offer is the Optronics Mini Rectangular Clearance Light, part # A91AB. This is an amber light that measures 2-1/2 inches long x 1-3/16 inches wide x 7/8 inch deep.

This light requires the # A91LW pigtail to complete the wiring and a mounting bracket.

The bracket is available in black, part # A91BB. For a chrome finish, use # A91CB.

expert reply by: Jeffrey L

0

Answer 1

The Optronics Flush Mount Grommet for #AL91AB Series Trailer Clearance and Side Marker Lights #A91GB, will fit a hole that measures 2-7/8 inches across and 1-1/2 inches tall.

view full answer...

Answer 2

The “SAE P2PC 98” you provided is a code used by the department of transformation and will not have any bearing on the correct replacement. In order to determine the correct replacement I would need you to either A) remove the lens and find the…

view full answer...

Answer 3

Thank you for the light measurements on your 1998 Trailstar Boat Trailer. For the left and right front marker lights, I recommend the #MCL82AB LED Trailer Clearance or Side Marker Light w/ Reflex Reflector. These measure 4-7/16" long x…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...