Recommended Locks for B&W Stow and Go Ball Mount in Hitch

Question

Question:

Which locks would you get for this hitch?

asked by: Troy W

0

Expert Reply:

The hitch lock I recommend for the B&W Stow and Go Ball Mount # BWTS10047B, you were looking at, is the # BX8858.

Currently, there is no lock available that will replace the adjustable pins on the B&W ball mount. If your coupler is locked to the hitch ball it would take someone with this exact ball mount assembly to be able to steal your trailer so it would be highly unlikely.

I have linked the above mentioned products to this page for your viewing and purchasing convenience.

expert reply by: Jackie C

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

From the center of the first hitch pin hole to the back of the mounting block measures 3" for the B&W Tow & Stow 3-Ball Mount #BWTS10048B. That same measurement, when taken from the second hitch pin hole, is 4-1/8" on center. I hope…

view full answer...

Answer 3

I went to the warehouse to take some measurements and found that from the top of the receiver to the bottom of the 2-5/16" hitch ball was approximately 10-1/2" for the B&W Tow & Stow 3-Ball Mount with 5" of drop #BWTS10048B…

view full answer...

Answer 4

Thanks for reaching out! The measurements you're asking for on the B&W Tow & Stow 3-Ball Mount #BWTS10047B can be found on the attached image. I'm also linking a review video for you to reference!

view full answer...

Answer 5

The Curt Multi-Ball Adjustable Ball Mount #D900 does weigh 45 lbs. If you wanted a lighter tri-ball setup you'd want to look into something like the B&W Tow & Stow 3-Ball Mount #BWTS10047B which only weighs 28 lbs and has the same specs…

view full answer...

Answer 6

B and W recommends their hitch lock part #BX8858 for use with the Stow and Tow Ball Mount part #BWTS10047B that you referenced.

view full answer...

Answer 7

If you have exactly 11 inches from the ground to the bottom of the B&W Tow & Stow 3-Ball Mount #BWTS10048B you'd be totally fine. It only might be an issue if you went on unusually uneven terrain like off-roading. But 11 inches would be…

view full answer...

Answer 8

The Curt Adjustable 2-Ball Mount #C99NR uses Pins #C56NR which are 3/4" in diameter and have a usable length of 3-3/4". You will need the InfiniteRule Lock #IR36FR which is also 3/4" in diameter with a 3-7/8" span to lock the…

view full answer...

Answer 9

For your 2014 Nissan Pathfinder Platinum you'll want to measure the coupler height of your trailer and the hitch height of your trailer hitch to confirm the correct ball mount, but you'll more than likely want the B&W #BWTS10048B. This…

view full answer...

Answer 10

I'll start off by saying that it's a bit unusual that your Ford Super Duty truck receiver is lower than the trailer you're towing, so if those measurements are accurate then you'll need a ball mount with a 2 inch rise. If you're…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...