12-Volt Accessory Power Feed on 7-Way Trailer Connector Not Working on 2006 Chevy Silverado 2500HD

Question

Question:

I just installed one of your brake controller on my 2006 silverado 2500HD diesel. The truck has the factory tow package with the factory 7 way. I plan on pulling a camper and I need to get power to the hot 12v at the plug to charge the battery on camper. Is there a fuse or a wire I need to hook up?

asked by: Jeff

0

Expert Reply:

If you aren't getting power on that connector pin on the 7 way, take a look at the power distribution box under the hood. Once you remove the cover, you will see two posts on the side of the box closest to the motor. The post closest to the front should have a wire attached to it. Near the post, there should be a 40 amp fuse in place to fuse the circuit.

Take a look at the FAQ article I've linked for you. In step 'F' shows the location of the post and the fuse that I'm talking about. Make sure the fuse is inserted and is not blown, and make sure the wire is attached, and your 12V feed should work.

expert reply by: Mike L

0

Answer 1

The tow package wiring is typically located under the dash between the area of the emergency brake pedal and the steering column. The wiring harness will have a red/black, a dark blue, a light blue, an orange and a white wire. Many times this…

view full answer...

Answer 2

It sounds like there may be an issue with the wiring in the trailer to the hydraulic brake actuator. When you installed the Adapter Module #DX35FR you did receive the trailer connected message. I have attached the instructions for the Adapter…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Answer 10

This will depend on if you have disc or drum brakes on your triple axle boat trailer. Disc Brake Kit #HS381-9067 Drum Brake Kit #HS381-9066 Each kit contains the correct electric over hydraulic actuator, 7-way wiring and breakaway components. If you…

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 12

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...