Can Level 3 of the Edge EZ for Dodge Cummins # EP30204 Be Used While Towing

Question

Question:

I have a 2006 5.9 cummins with the g-56 6spd and im running the edge ez. Im wondering if its ok to run it on setting 3 while towing. A former ez owner said it wouldnt hurt it since its a manual just wanting some advice from experts before i try it.

asked by: Andrew N

0

Expert Reply:

Yes, you could run the level 3 of your Edge EZ for Dodge Cummins # EP30204 on your 2006 Ram with a Cummins while towing. That is what this product was intended to do. Give you additional power while towing.

expert reply by: Jameson C

0

Answer 1

I am not sure which wire or step of the installation process you are referring to but I will walk you through the entire process below for future reference. In order to install the Edge EZ for Dodge Cummins 5.9L part #EP30203 on your 2003 Dodge Ram…

view full answer...

Answer 2

The toggle switch with the Edge EZ programmer #EP30204 is needed to select the power level you want. If you do not want to mount the switch inside the vehicle then you could leave it under the hood as long as the cable and switch are protected and…

view full answer...

Answer 3

Here are the different power levels for the Edge EZ for Dodge Cummins 5.9L #EP30204 that you referenced: Level 1: 25 Horsepower - 50 Foot Pounds of Torque Level 2: 45 Horsepower - 75 Foot Pounds of Torque Level 3: 65 Horsepower - 150 Foot Pounds of…

view full answer...

Answer 4

For a 2003 Dodge Ram with a Cummins engine the needed Edge EZ module is the part #EP30203. What you sent in a picture of is for an older Cummins truck.

view full answer...

Answer 5

I spoke to my contact at Edge Technical about a way to turn the Edge EZ Module #EP30204 off. My contact said that you will need to unplug the module in order to take the vehicle back to stock. There is not a 4th position on the switch.

view full answer...

Answer 6

According to my contact at Edge Products their Edge EZ performance tuner for the Dodge Cummins, part #EP30204, does not have a specific trailer weight that makes its Stage 2 power level unsuitable. He advised that based on your familiarity and towing…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Can Level 3 of the Edge EZ for Dodge Cummins # EP30204 Be Used While Towing

Product Page this Question was Asked From

Continue Researching