Replacement Wheel Stud Recommendation for Kodiak Disc Brake Kit K2HR712

Question

Question:

will it kodiak K2HR712 disk brake rotor

asked by: Rafael

0

Expert Reply:

Yes, if you are looking for replacement wheel studs for your Kodiak Disc Brake Kit you would want the part # K12WB2.

expert reply by: Jameson C

0

Answer 1

The closest wheel stud we offer to the size you need is the Kodiak Wheel Bolt - 1/2" Diameter x 2" Long, part #K12WB2. This wheel stud has a knurl of .540, which is slightly larger than the .525 you specified in the question. I…

view full answer...

Answer 2

When you bleed the brakes on your trailer after installing the Kodiak Calipers #KDBC225DAC, you will want to start with the brake that is furthest away from the actuator. Of the two bleeder valves, you will want to use the bleeder valve that is on…

view full answer...

Answer 3

The Kuat NV 2.0 bike rack you referred to, part #NV22G would work great in the hitch on your truck when you use an adapter like part #HT02. The rack is NOT recommended for use on the rear of a towed travel trailer. Bike racks installed on the rear of…

view full answer...

Answer 4

Based on the dimensions of your old studs the part #K12WB2 that you referenced is exactly what you'd need. The .02 inch diameter difference you mentioned for the splines ensures that the stud fits tightly. I attached a review video for this stud…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

As you have a Coleman Mach system currently you can use the Furrion Chill AC units from the list below. These will simply replace only the rooftop units and the controls and thermostats you currently have in place with control the new AC's. 13.5K…

view full answer...

Answer 7

Looks like you have a spline diameter of .56 inches and and threaded portion of 1/2 inch which is very popular. For that you'd want the part #K12WB2. I attached a picture that has a dimensional diagram for you to check out as well.

view full answer...

Answer 8

Hello Pat, thanks for reaching out. All of the 1/2" x 20 wheel studs we offer have a .545" knurl diameter. If you can make that work, I recommend the DeeMaxx Drive-In Wheel Stud #DE52GR which is 2" long overall, or the #DE45GR which is…

view full answer...

Answer 9

Hi Lane, The closest option we have to the measurements you provided would be the DeeMaxx Drive-In Wheel Stud - 1/2" Diameter x 2" Long #DE52GR.

view full answer...

Answer 10

Based on the dimensions of the wheel stud you sent in a picture of the part #K12WB2 would be what you'd need.

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 12

I am happy to help you replace the wheels studs but it will require some measuring with digital calipers like part #PTW80157. I have attached a diagram with the measurements needed to get the correct replacement. Once you can provide me with the A,…

view full answer...

Replacement Wheel Stud Recommendation for Kodiak Disc Brake Kit K2HR712

Product Page this Question was Asked From

Continue Researching