Will Pull Out Steps fit 2011 Palomino Puma 27KFQ

Question

Question:

Hello, Looking for a bolt on replacement for my current manual 24inch wide double step. Will this version bolt on or do I need a different version? Trailer is a 2011 Palomino Puma 27KFQ Thanks

asked by: Steve K

0

Expert Reply:

The Manual Pull Out Steps part # SMFP-2100 that you mentioned are going to fit your 2011 Palomino Puma 27KFQ only when you use the Lippert Outriggers for Manual RV Steps # LC301704. If you need a smaller step you can use # SMFP-2120 instead. The mounting locations are different, so the outriggers are needed with either option.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Flexco Manual Pull-Out Steps for RVs - Double - 7-7/8" Drop/Rise - 24" Wide - 350 lbs #SMFP-2100 are from Stromberg-Carlson and are Flexco model steps. So in other words they are one in the same. I included some pictures showing dimensions…

view full answer...

Answer 2

The Flexco steps, part #SMFP-2120, have six holes on each side. The top set is 4-1/2 inches center on center and both the lower sets are 9-1/2 inches. Additionally the top holes measure 7 inches center on center between the bolt holes front to back…

view full answer...

Answer 3

From the photos I've seen of your 2015 FR Shasta Flyte 215CK, it looks like you need a 2-step unit. To identify the correct replacement, you'll want to determine the width of the mounting base of your existing steps. If that base is about…

view full answer...

Answer 4

Trailer makers typically do not maintain details about items like the steps that they install on their RVs so for you to select a 2-step assembly to replace a single-step unit you'll just need to note some basic dimensions. First, you want to…

view full answer...

Answer 5

The distance between the mounting holes on the sides of the Flexco Manual Pull-Out Steps for RVs #SMFP-2100 that you referenced is 4-1/2 inches.

view full answer...

Answer 6

The mounting holes on the Flexco Manual Pull-Out Steps for RVs #SMFP-2100 are 7" apart on the same side of the bracket and 24-1/2" apart across from each other. I have included a picture showing these measurements as well as a few…

view full answer...

Answer 7

After looking at some pictures of your 1992 Bounder built on a P30 chassis it would seem that step setup with 2 steps would be about ideal based on the height of your motorhome. With that being said I believe the RV Manual Pull Out Step #SMFP-2120…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...