Distance Between Mounting Holes on Side of Flexco Manual Pull-Out Steps for RVs

Question

Question:

What is the on-center measurement for side mounting bolt pattern for 24inch folding 2-step? I did not see in your video or schematics. My steps attach from the side, not the top. I have a 2017 Coachman Clipper 17FB with one step at this time. Thank you

asked by: Michael G

0

Expert Reply:

The distance between the mounting holes on the sides of the Flexco Manual Pull-Out Steps for RVs # SMFP-2100 that you referenced is 4-1/2 inches.

expert reply by: Jameson C

0

Answer 1

Flexco Manual Pull-Out Steps for RVs - Double - 7-7/8" Drop/Rise - 24" Wide - 350 lbs #SMFP-2100 are from Stromberg-Carlson and are Flexco model steps. So in other words they are one in the same. I included some pictures showing dimensions…

view full answer...

Answer 2

The Flexco steps, part #SMFP-2120, have six holes on each side. The top set is 4-1/2 inches center on center and both the lower sets are 9-1/2 inches. Additionally the top holes measure 7 inches center on center between the bolt holes front to back…

view full answer...

Answer 3

Trailer makers typically do not maintain details about items like the steps that they install on their RVs so for you to select a 2-step assembly to replace a single-step unit you'll just need to note some basic dimensions. First, you want to…

view full answer...

Answer 4

From the photos I've seen of your 2015 FR Shasta Flyte 215CK, it looks like you need a 2-step unit. To identify the correct replacement, you'll want to determine the width of the mounting base of your existing steps. If that base is about…

view full answer...

Answer 5

The Manual Pull Out Steps part #SMFP-2100 that you mentioned are going to fit your 2011 Palomino Puma 27KFQ only when you use the Lippert Outriggers for Manual RV Steps #LC301704. If you need a smaller step you can use #SMFP-2120 instead. The…

view full answer...

Answer 6

The mounting holes on the Flexco Manual Pull-Out Steps for RVs #SMFP-2100 are 7" apart on the same side of the bracket and 24-1/2" apart across from each other. I have included a picture showing these measurements as well as a few…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Distance Between Mounting Holes on Side of Flexco Manual Pull-Out Steps for RVs

Product Page this Question was Asked From

Continue Researching