Will Roadmaster Rollaway Trailer Hitch Protector # RM-050 Fit a Curt Hitch part # C13105

Question

Question:

Hi, I have the C13105 Curt hitch receiver on my 2008 Sienna... Wondering if the Roadmaster RM-050 will fit on the C13105. Thanks!

asked by: Carl

0

Expert Reply:

Yes, the Roadmaster Rollaway Trailer Hitch Protector # RM-050 that you referenced will fit the Curt Hitch part # C13105 that you referenced because it is a 2 inch hitch like what this is designed to fit.

expert reply by: Jameson C

0

Frank H.

2/14/2024

would i only need to drill out the side where the threaded portion fits? You happen to know the diameter of the threaded portion?

Reply

Jameson C.

2/16/2024

@FrankH The Roadmaster # RM-050 that you referenced does not have a threaded portion actually so there's no need to drill anything out.

Reply

Frank H.

2/19/2024

@JamesonC I am referring to the bike rack locking hitch pin I mentioned, its threaded on one end and you said it wouldn't fit thus my question about enlarging the hold to accommodate the lock hitch pin which screws into the bike rack.

Reply

Jameson C.

2/20/2024

@FrankH I can't find any reference to a bike rack anywhere so I am not sure what rack you have. Did you ask a different question using a different email? In general we don't recommend drilling out the threaded hitch pins.

Reply

See All (5) Replies to Frank H. ∨

Answer 1

The Roadmaster Rollaway Trailer Hitch Protector #RM-050 will likely work with your trailer hitch that has the tabs on the bottom of the receiver as there does not look like there is going to be any interference. So long as the tabs are completely on…

view full answer...

Answer 2

The solution I would offer involves a roller unit such as the Roadmaster Rollaway Trailer Hitch Protector, part #RM-050. The Rollaway CAN be used while towing, without interfering with the ball mount or accessory.

view full answer...

Answer 3

Yes, the Roadmaster Rollaway Skid Wheel part #RM-050 will fit the Curt hitch you have installed part #13358. To determine where the roller will be relative to the hitch height you'd need to measure 3-1/4 inches down from the hitch pin hole.…

view full answer...

Answer 4

Roller #RM-050 is a good option for a Class III trailer hitch on your 2006 Honda Odyssey. It does hang down lower than the hitch receiver so it will actually make contact with the ground sooner than if the roller were not on it. This roller will not…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 12

The 2,500 lb weight rating for the Hellwig Pro Series Helper Springs #HE47QR is a great option for your 2022 Mercedes-Benz Sprinter 3500 since motorhomes tend to have a bit more weight to them. These springs are also considered progressive so they…

view full answer...

Will Roadmaster Rollaway Trailer Hitch Protector # RM-050 Fit a Curt Hitch part # C13105

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching