Availability of 1/2-Inch Hex Nut with 13/16-Inch Wrench Flats

Question

Question:

Am looking for black half inch panel hex nuts with fine threads.

asked by: Randy

0

Expert Reply:

We do offer a fine-thread 1/2-inch hex nut, part # CE11051, which is a trailer wheel lug nut with a 60-degree coned profile on the outside surface. The rear surface is flat. This item is uncoated steel so you can paint it black if you wish. Take care to keep paint out of the threads. It takes a wrench size of 13/16ths-inch.

expert reply by: Adam R

0

Answer 1

I have attached a chart that has the torque settings for lug nuts. The torque settings are based on the lug size, type, wheel size, and material. The 6 marks you have on the lug means it is a grade 8 high strength lug bolt. For example, for a 15-inch…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 4

The only difference in the Demco Channel Tongue Trailer Couplers #DM16080-95 and #DM15931-95 is going to be the bolt pattern. One will have the 5-Bolt hole pattern and the other is going to have 4-Bolt holes. I have included images below showing the…

view full answer...

Answer 5

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 6

Thank you for the image. It appears you will need either the Demco Channel Tongue Trailer Coupler #DM13203-95 or #DM16080-95. Both of these couplers have a zinc coating for increased corrosion resistance and fit on a standard 3" wide channel…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

You can certainly go ahead and re use the existing 2 bolts, provided they are in good condition. The fish wire method shown in the video works too, but it is also very common to just use the two bolts like your old Atwood actuator. Personally I would…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Two bolts will be sufficient for installing the Demco Hydraulic Brake Actuator #DM72VR. You will want to use two Requires 2-1/2" x 4-1/2" Grade-5 of Grade-8 bolts. Personally I would use something like the Curt Coupler Hardware Kit #C25388.…

view full answer...

Availability of 1/2-Inch Hex Nut with 13/16-Inch Wrench Flats

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching