Replacement 7-Way/4-Pole Trailer Socket for 2002 Ford F-250

Question

Question:

Have a broken wire on 2002 f250 super duty, looks like you might have a harness that will work. original part # 2c3z-13a576 da all parts i found are for 2002 -2004 f250 super duty only need the 7 pin harness original has a 4 pin also can you help??? thanks!!

asked by: Steve W

0

Expert Reply:

For a 2002 Ford F-250 with factory-installed combination 7-way/4-pole socket you can use Reese Multi-Tow 7-Way & 4 Pole Trailer Connector # 74682. This will plug in at the round U.S. Car connector behind the rear bumper as shown in the linked video.

expert reply by: Adam R

0

Answer 1

While we don't have a replacement hardware kit we can offer you for the #BWGNRK1016 I did attach a picture that shows all of the hardware you'd need that you could source at a local hardware store. I also attached an install video link for…

view full answer...

Answer 2

It sounds like your truck will use a 7-way harness like Hopkins #40167 which uses connectors like what you describe. Please refer to the linked photo that shows those connectors. This includes a 7-way socket that plugs into the included round U.S.…

view full answer...

Answer 3

The Firestone Ride-Rite air bags that fit your 2002 Ford F-350 are the Firestone Ride-Rite Air Helper Springs #F2550, and according to the manufacturer, these ARE compatible with an in-bed hitch, so you can definitely add a 5th wheel hitch to your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...