What is the Distance Between Mounting Holes on the Pack'Em Trimmer Rack # PK-6

Question

Question:

What is the distance between the two pre-drilled holes on the PackEm Trimmer Rack # PK-6?

asked by: Matt

0

Expert Reply:

I went out to the trailer on which we installed Pack'em trimmer rack # PK-6 and found that the mounting holes are 10 inches apart on center.

expert reply by: Michael H

0

click to enlarge

Answer 1

What a lot of folks have done is used flexible rubber tubing and slipped it over the hooks of the #PK-6 trimmer racks to prevent the metal on metal contact. The smaller hooks (see photo) are about 5/8 in diameter. Find some clear plastic tubing with…

view full answer...

Answer 2

I have included a picture with the vertical distances for you to see. The overall height of the Pack'em Trimmer Rack #PK-6 is 46". It is capable of holding 3 trimmers with a trimmer pole that is 1-5/8" in diameter or smaller. The…

view full answer...

Answer 3

There is no recommended center to center distance for the Pack Em Trimmer Rack, #PK-6, but they must be mounted a minimum of 3ft apart. Trimmers come in different sizes and lengths, so it is best to mount the racks to fit your specific trimmers. The…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Since your 5' x 10' traler has a V-nose, we recommend going with the Adco SFS AquaShed Trailer Cover For Trailers up to 12' Long #290-46002. This will allow a bit of extra room for the V-nose. With the included straps on the front and…

view full answer...

Answer 6

I recommend the Redarc Tow-Pro Elite Brake Controller for Tekonsha Harness item #RED63RR. This brake controller and harness will install inside your Silverado without cutting or splicing wires using the Tekonsha Plug-In Wiring Adapter item #3064-P.…

view full answer...

Answer 7

Yes, the Pack'Em Rack for Open Utility Trailers #PK-6-OP1 is compatible with your 2' high trailer sides. The supports don't necessarily have to rest on the floor of your trailer so you can raise them to whatever height is needed for your…

view full answer...

Answer 8

The part number "TCM22333TBN" that you referenced on your grease seal cross-references to the Grease Seals 10-36 part #RG06-070. If you need any other parts for your trailer hubs i.e. bearings or races, I would need to know either the part…

view full answer...

Answer 9

The Lockable Blower Rack for Utility Trailers #RA-19 is 39-1/2 inches tall and 13-1/2 inches wide. The 12 inch mesh sides will not support this rack, so you will need further bracing to your trailer like a rail to give you the stability needed to…

view full answer...

Answer 10

The Pack'Em Rack for Open Utility Trailers part #PK-6-OP1 does not come with any of the added accessories shown on the product page (i.e. cooler, leaf blower, lawn trimmer). The accessories are included in the photo to give customers a better…

view full answer...

Answer 11

The Pack'Em Racks #PK-6-OP1 themselves measure 46 inches. From the top mounting holes to the top of the racks they measure 36 inches. See attached picture.

view full answer...

Answer 12

You are definitely doing the right thing by changing out passenger car tires and putting trailer tires on your trailer. Trailer tires have a sidewall that is a little more rigid and so they can handle the weight of trailers and their cargo much…

view full answer...

What is the Distance Between Mounting Holes on the Pack'Em Trimmer Rack # PK-6

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching