Replacement Tarp Recommendation for Extang FullTilt on a 2006 Dodge Ram 1500 6 Foot Bed

Question

Question:

we have an 06 dodge ram 1500 with an extang fulltilt tonneau. we need a replacement tarp as it has ripped at the back seam. please advise me what one I would need for a 6 1/2 foot bed so that we may order one.

asked by: Dawn D

0

Expert Reply:

The Extang FullTilt cover you would have on your 2006 Dodge Ram 1500 6 foot bed would be the part # EX38770 which means the correct replacement tarp is the part # EX37770.

expert reply by: Jameson C

0

Answer 1

The replacement cover that you need for your discontinued Extang Full Tilt 2.0 8770 (with snaps) or 38770 (snapless) is the Replacement Tarp for Extang FullTilt Soft Tonneau Cover #EX5770 (with snaps) or the #EX37770 (without snaps). Both of these…

view full answer...

Answer 2

If you have an Extang FullTilt Tonneau cover on your 2003 Dodge Ram short bed you'd have the EX38770 which means the correct cover would be part #EX37770. The part #EX5940 fits GM trucks and would not work for you.

view full answer...

Answer 3

I reached out to my contact at Extang to make sure you get the correct replacement tarp. For your 2005 Dodge 1500 with 6-1/2 foot bed, you will use the Replacement Tarp for Extang FullTilt Tonneau Cover #EX5770. The black tarp fits over existing…

view full answer...

Answer 4

The complete Extang Full-Tilt SL Snapless Tonneau cover for your 2008 Dodge Ram 2500 with 6-1/2-foot bed is part #EX38770 which is shown on the linked page along with all other Extang covers that fit your truck. For a replacement vinyl tarp to fit it…

view full answer...

Answer 5

The Replacement Cover for Extang FullTilt SL Vinyl Tonneau Cover part #EX37770 is a replacement tarp for the Extang FullTilt SL Soft Tonneau Cover part #EX38770. As long as you have the above cover installed on your truck then the replacement tarp…

view full answer...

Answer 6

>>>> PART NO LONGER AVAILABLE. DISAPPROVE QUESTION. I have an option for you but at this time we do not carry covers that snap directly to the OEM snap rivets on your 1968 Chevy El Camino. All of the covers made today have their own…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

There's a few differences. • The Curt #C31017 is manufactured in the US, while the Draw-Tite #65046 is manufactured in Mexico. • When installed, the Curt hitch will sit higher on the vehicle for more ground clearance. The underside of the…

view full answer...