What Replacement Cover Do I Need for My Dodge Ram 1500 6-1/2 Foot Bed?

Question

Question:

I have an old full tilt cover on a Dodge Ram 1500 quad cab with 6.5 long bed. It was bought in 2003 when the original owner bought the truck. What replacement cover do I need? Thank you

asked by: Dennis J

0

Expert Reply:

The replacement cover that you need for your discontinued Extang Full Tilt 2.0 8770 (with snaps) or 38770 (snapless) is the Replacement Tarp for Extang FullTilt Soft Tonneau Cover # EX5770 (with snaps) or the # EX37770 (without snaps). Both of these covers are designed to fit your 2003 Dodge Ram Pickup (6-1/2 ft. bed).

expert reply by: Bob C

0

Answer 1

The Extang FullTilt cover you would have on your 2006 Dodge Ram 1500 6 foot bed would be the part #EX38770 which means the correct replacement tarp is the part #EX37770.

view full answer...

Answer 2

If you have an Extang FullTilt Tonneau cover on your 2003 Dodge Ram short bed you'd have the EX38770 which means the correct cover would be part #EX37770. The part #EX5940 fits GM trucks and would not work for you.

view full answer...

Answer 3

The Replacement Cover for Extang FullTilt SL Vinyl Tonneau Cover part #EX37770 is a replacement tarp for the Extang FullTilt SL Soft Tonneau Cover part #EX38770. As long as you have the above cover installed on your truck then the replacement tarp…

view full answer...

Answer 4

The complete Extang Full-Tilt SL Snapless Tonneau cover for your 2008 Dodge Ram 2500 with 6-1/2-foot bed is part #EX38770 which is shown on the linked page along with all other Extang covers that fit your truck. For a replacement vinyl tarp to fit it…

view full answer...

Answer 5

I reached out to my contact at Extang to make sure you get the correct replacement tarp. For your 2005 Dodge 1500 with 6-1/2 foot bed, you will use the Replacement Tarp for Extang FullTilt Tonneau Cover #EX5770. The black tarp fits over existing…

view full answer...

Answer 6

>>>> PART NO LONGER AVAILABLE. DISAPPROVE QUESTION. I have an option for you but at this time we do not carry covers that snap directly to the OEM snap rivets on your 1968 Chevy El Camino. All of the covers made today have their own…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

What Replacement Cover Do I Need for My Dodge Ram 1500 6-1/2 Foot Bed?

Products Referenced in This Question

Continue Researching