Transmission Cooler Recommendations for a 2002 F-350 with the 7.3L Diesel

Question

Question:

I have a 2002 F-350 with the 7.3L diesel and 190,000 miles on it, I had the transmission rebuilt about three years ago and when I tow trailers 5th wheel and a car trailer weighing anywhere from 3000-13,900#s, my transmission temperature rises sometimes to 240 degrees and it starts to spit out transmission fluid. I have an aftermarket transmission pan Mag-hytech that holds another 8 quarts, I believe. My question is: will going to a more efficient transmission cooler help? I am not sure if my stock cooler is tired but I would like to try changing it out to see if it helps. Afterall, transmission coolers are inexpensive and it might solve the problem or it might not.

asked by: Matt W

0

Expert Reply:

Transmission fluid should run below 200 degrees Fahrenheit. At 240 degrees you definitely need to make some sort of change to reduce the temperature. I would first recommend having the transmission checked by a qualified automotive technician to be sure it is performing properly. This will assure you that no damage has been caused to the transmission and you will not be stranded. Installing a transmission cooler will not reverse any damage that may have already been caused.

If you find that your transmission is in good shape then a transmission cooler is definitely recommended. You cannot cool transmission fluid too much and the largest cooler that will fit in front of the radiator or air conditioner condenser is the cooler I would recommend for maximum cooling. Your Ford should have room to accept the largest, most efficient transmission cooler that we carry. The Derale Series 8000, Class IV, Plate-Fin Transmission Cooler Kit w/Barb Inlets, item # D13504, is the best cooler we carry and should fit easily on your 2002 F-350 with 7.3L diesel.

You will also need the Derale Radiator Adapter Fittings for Ford, Lincoln, and Mercury, item # D13025, if you wish to avoid cutting and flaring the existing transmission lines on your vehicle.

You will not remove or bypass your stock cooler. The new cooler will install inline with the existing transmission cooler return line on your truck. This way you still have the cooling provided by the stock cooler and add the cooling capacity of the Derale Series 8000 Plate-Fin Transmission Cooler, item # D13504.

expert reply by: Robert G

0

Answer 1

Thank you for the photo of your sturdy F-350 that is in need of a little TLC in the form of a transmission cooler to help it when pulling those heavy loads. For your heavy-duty application you'll want a high-efficiency cooler that will give…

view full answer...

Answer 2

I do have an option for you but the location of the crossbars is rather important as these are the points on the roof that the roof rack manufacturer have determined are suitable for weight bearing loads. I understand you want to place the…

view full answer...

Answer 3

You should not need to use a filter extender to install this Derale Transmission Pan Cooler #D14208 in your 2001 Ford F-350. I spoke with my contact at Derale to confirm this also.

view full answer...

Answer 4

In order to remove the check engine light that is associated with the installation of a DPF delete kit on your 2012 Ford F-250 with 6.7L V8 diesel engine and make sure it stays off, you would need to have a custom tune performed on the vehicle. In…

view full answer...

Answer 5

The method we use to determine the correct line to install a transmission cooler on is pretty simple. You want to install the cooler on the return line. To determine which line is the return line you will want to start with your truck totally…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...