Draw Tite Front Hitch Recommendation for a 2005 Chevy Silverado 1500 LD

Question

Question:

65028 item will this fit the silverado 1500 not HD front hitch

asked by: Michael

0

Expert Reply:

I have a front hitch that is a confirmed fit for your 2005 Chevy Silverado 1500 LD, but the part # 65028 is only for the HD models. Instead, you would want the Curt part # 31302 which is a confirmed fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Beginning with the introduction of the 2007 model year, GM stopped using the connector that was located in the convenience center under the dash for installing a brake controller. Instead, the tow package connection consists of 4 or 5 wires bundled…

view full answer...

Answer 2

The Curt #31302 is a confirmed fit and will be a great choice for you. This hitch will prove durable over time because they use a slightly thicker powder coat than other brands. This hitch will require trimming your air dam, but you won't…

view full answer...

Answer 3

The Draw-Tite Front Mount Trailer Hitch Receiver part #65078 is for the 2500 and 3500 models whereas you have a 1500 model which has an entirely different front end. The bolt holes for the above hitch would not line up with those on your frame and…

view full answer...

Answer 4

The Curt Class V Trailer Hitch, #C15313, was designed to fit the 2500 HD models of the 2005 Chevrolet Silverado, but it has not been confirmed to fit the cab and chassis models like your service body truck. The important factor to consider is the…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 10

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Draw Tite Front Hitch Recommendation for a 2005 Chevy Silverado 1500 LD

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching