Does the Felt Strip of CIPA Towing Mirror part # CM11301 Permanently Attach to Vehicle Mirror

Question

Question:

I have an installation question on the towing mirrors, part number CM11301. The instructions mention affixing a felt strip to this wedge. Does this wedge stay glued to the existing mirror once you take CM11301 off for everyday driving?

asked by: Jim M

0

Expert Reply:

The felt strip of the CIPA Towing Mirror part # CM11301 that you referenced would not permanently attach to the mirror of the vehicle. When you remove the tow mirror from the vehicle the felt would come off of the vehicle as well.

I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Since you want support, ride quality, and would prefer an economical price the SumoSprings Solo kit part #SSR-610-54 would be exactly what you want for your 2016 Toyota Tundra. This is the best blend of the things you are wanting and will do a great…

view full answer...

Answer 2

The part #CM11300 is a set of tow mirrors that includes the passenger and the driver side whereas the part #CM11301 is just the driver side and part #CM11302 is just the passenger side.

view full answer...

Answer 3

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...